State Industries Green Choice instruction manual

Page 13

11.Install the vent collar assembly through the wall, connecting it to the extension and/or elbow (depending on which one was used).

FIGURE25.

12.We have supplied four wood screws to temporarily attach the collar to the exterior wall of the building. However, other types of screws may have to be substituted depending on the material used in the construction of the exterior wall.

15.The vent cap has four holes around the outer edge. Remove the four screws used to temporarily attach the collar to the exterior wall. Then secure the vent cap assembly with the vent collar assembly to the exterior wall using the same four screws.

NOTE: Screws are supplied: However, substitution may be necessary depending on the exterior wall material.

FIGURE26.

13.Insert the 3” (76 mm) diameter flue extension pipe into the vent collar assembly (flared & notched end first) and lock (turn clockwise to lock studs to slots) the flue extension pipe to the flue elbow.

FIGURE28.

16.Go back indoors toattachinsidecollartotheinsidewall.Placethe collar against the wall. Secure to wall by using four long sheet metal screws.

NOTE: Screws are supplied: However, substitution may be necessary depending on the interior wall material.

FIGURE29.

14.Connect the vent cap by sliding its end over the 3” (76 mm) diameter extension pipe and O-ring.

NOTE: To facilitate ease of assembly of the vent cap to the 3” (76 mm) pipe, a soap solution can be applied to the O-ring gasket.

17.Using the tube of sealant supplied, run an ample amount of sealant around the edge of the vent pipe where it is inserted through the inside collar to seal air drafts from wall.

FIGURE27.

FIGURE30.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Residential Direct Vent GAS Water Heaters Important Definitions Safe INSTALLATION, USE and ServiceGeneral Safety Introduction Table of ContentsGET to Know Your Water Heater GAS Models Typical InstallationMixing Valve Usage Facts to Consider about the Location Locating the NEW Water HeaterVenting Clearances Combustion Air and VentilationFlue Extensions Optional Wire GrillChart #2 Chart #1Vertical Height Extension Kit Horizontal Extension KitStandard Vent Kit Installation #1 ALL InstallationsCutting The Opening Through The Outside Wall Water Heater AttitudePage Page BTU’s in 1000’s NAT./L.P Chart #3 GAL CAPPage Page Optional Horizontal Vent Kit Installation #3 Page Through The Outside Wall. See Optional Vertical and Horizontal Vent Kit Installation #4Chart #4 GAL CAP Collar Optional Vent Cap Porcelain-Enameled Page Page Water Piping Installing the NEW Water HeaterValve and Pipe Insulation TEMPERATURE-PRESSURE Relief ValveFilling the Water Heater GAS Piping Sediment Traps GAS Piping with Flexible ConnectorGAS Piping with ALL Black Iron Pipe to GAS Control Before Lighting the Pilot Installation ChecklistPage For Your Information Temperature RegulationStart UP Conditions CondensateOperational Conditions Burner Cleaning Periodic MaintenanceGAS Control Valve & Burner Assembly Venting System InspectionHousekeeping TEMPERATURE-PRESSURE Relief Valve OperationAnode ROD Inspection DrainingLeakage Checkpoints Drain Valve Washer ReplacementRepair Parts List BTU’s in 1000’s NAT/L.P 36/36 38/38 40/40 48/44 55 NAT Parts GAL. CAP KEY # DescriptionRepair Parts List BTU’s in 1000’s NAT/L.P 36/36 38/38 40/40 48/44 This is a Repair Parts LIST, not a Packing ListTroubleshooting Guidelines Page Page

Green Choice specifications

State Industries Green Choice is a remarkable initiative designed to promote energy efficiency and environmentally-friendly practices in the manufacturing sector. The program focuses on providing high-efficiency appliances and heating systems that are not only cost-effective but also reduce environmental impact. With a growing concern about climate change, State Industries aims to address these issues through innovations in technology and sustainable practices.

One of the main features of the Green Choice initiative is its commitment to producing ENERGY STAR® certified products. These appliances meet strict energy efficiency guidelines set by the U.S. Environmental Protection Agency, helping consumers save money on energy bills while also decreasing their carbon footprint. By prioritizing energy efficiency, State Industries ensures that their products move the industry toward a more sustainable future.

Incorporating advanced technologies is central to the Green Choice initiative. The use of state-of-the-art insulation materials minimizes heat loss, while high-efficiency burners and heat exchangers maximize energy utilization in heating systems. These technological innovations lead to significant reductions in energy consumption, translating to both financial savings for consumers and reduced greenhouse gas emissions.

Another characteristic of Green Choice is the emphasis on using sustainable materials in manufacturing. State Industries strives to source materials that are either recyclable or derived from renewable resources. This commitment not only supports the economy but also minimizes waste and environmental degradation associated with traditional manufacturing processes.

Furthermore, State Industries prioritizes lifecycle analysis in the development of its products. This approach evaluates the environmental impact of a product from its conception through production, usage, and eventual disposal. By understanding the full lifecycle, State Industries can make informed decisions that enhance the sustainability of its offerings.

Consumer education is also a vital component of the Green Choice program. State Industries actively engages with customers to raise awareness about energy-efficient practices and the benefits of choosing sustainable products. By empowering consumers with knowledge, the initiative encourages responsible energy use and promotes a culture of sustainability.

In conclusion, State Industries Green Choice represents a holistic approach to manufacturing, focusing on energy efficiency, technological innovation, sustainable materials, and consumer engagement. This initiative not only helps to combat environmental issues but also fosters a market for eco-friendly products, paving the way for a more sustainable future. State Industries is setting a positive example in the industry by prioritizing ecological responsibility while delivering high-quality, efficient solutions to consumers.
Top Page Image Contents