State Industries Green Choice instruction manual Optional Horizontal Vent Kit Installation #3

Page 17

Optional Horizontal Vent Kit - Installation #3

If the vent hole has not been cut, refer to “Cutting The Opening Through The Outside Wall.” See page 11.

1.Lock the elbow to the straight 3” (76 mm) flue pipe. Set this assembly in place on the end of the water heater’s flue collar.

FIGURE52.

FIGURE54.

4.First remove the 3” (7.6 cm) horizontal extension from the elbow. Starting with the long end, which has four mounting holes, place the 6” (152 mm) diameter vent elbow over the 3” (76 mm) elbow. Bend the round end to fit the flared oval end of the jacket top.

FIGURE55.

5.Be sure the 6” (152 mm) diameter elbow is centered around the 3” (76 mm) diameter flue. Secure the vent pipe with four sheet metal screws at the connection at the jacket top.

2.Mark the flue collar at the slots in the elbow. Using a # 22 drill bit, drill holes into the collar at the two slots and secure the elbow to the collar with the screws provided.

NOTE: make sure elbow is properly aligned to the opening in the outside wall.

FIGURE53.

3.Using the tube of sealant supplied run an ample amount around the oval flare of the jacket.

FIGURE56.

NOTE: the standard kit includes a 3” (76 mm) flue extension and a 6” (152 mm) elbow extension. These parts will not be used with the horizontal kit.

6.Slide the vent collar (to be installed later) over the 6” (152 mm) vent elbow.

FIGURE57.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Residential Direct Vent GAS Water Heaters Important Definitions Safe INSTALLATION, USE and ServiceGeneral Safety Introduction Table of ContentsGET to Know Your Water Heater GAS Models Typical InstallationMixing Valve Usage Facts to Consider about the Location Locating the NEW Water HeaterVenting Clearances Combustion Air and VentilationFlue Extensions Optional Wire GrillChart #2 Chart #1Vertical Height Extension Kit Horizontal Extension KitStandard Vent Kit Installation #1 ALL InstallationsCutting The Opening Through The Outside Wall Water Heater AttitudePage Page BTU’s in 1000’s NAT./L.P Chart #3 GAL CAPPage Page Optional Horizontal Vent Kit Installation #3 Page Through The Outside Wall. See Optional Vertical and Horizontal Vent Kit Installation #4Chart #4 GAL CAP Collar Optional Vent Cap Porcelain-Enameled Page Page Water Piping Installing the NEW Water HeaterValve and Pipe Insulation TEMPERATURE-PRESSURE Relief ValveFilling the Water Heater GAS Piping GAS Piping with ALL Black Iron Pipe to GAS Control GAS Piping with Flexible ConnectorSediment Traps Before Lighting the Pilot Installation ChecklistPage For Your Information Temperature RegulationStart UP Conditions CondensateOperational Conditions Burner Cleaning Periodic MaintenanceGAS Control Valve & Burner Assembly Venting System InspectionHousekeeping TEMPERATURE-PRESSURE Relief Valve OperationAnode ROD Inspection DrainingLeakage Checkpoints Drain Valve Washer ReplacementRepair Parts List BTU’s in 1000’s NAT/L.P 36/36 38/38 40/40 48/44 55 NAT Parts GAL. CAP KEY # DescriptionRepair Parts List BTU’s in 1000’s NAT/L.P 36/36 38/38 40/40 48/44 This is a Repair Parts LIST, not a Packing ListTroubleshooting Guidelines Page Page

Green Choice specifications

State Industries Green Choice is a remarkable initiative designed to promote energy efficiency and environmentally-friendly practices in the manufacturing sector. The program focuses on providing high-efficiency appliances and heating systems that are not only cost-effective but also reduce environmental impact. With a growing concern about climate change, State Industries aims to address these issues through innovations in technology and sustainable practices.

One of the main features of the Green Choice initiative is its commitment to producing ENERGY STAR® certified products. These appliances meet strict energy efficiency guidelines set by the U.S. Environmental Protection Agency, helping consumers save money on energy bills while also decreasing their carbon footprint. By prioritizing energy efficiency, State Industries ensures that their products move the industry toward a more sustainable future.

Incorporating advanced technologies is central to the Green Choice initiative. The use of state-of-the-art insulation materials minimizes heat loss, while high-efficiency burners and heat exchangers maximize energy utilization in heating systems. These technological innovations lead to significant reductions in energy consumption, translating to both financial savings for consumers and reduced greenhouse gas emissions.

Another characteristic of Green Choice is the emphasis on using sustainable materials in manufacturing. State Industries strives to source materials that are either recyclable or derived from renewable resources. This commitment not only supports the economy but also minimizes waste and environmental degradation associated with traditional manufacturing processes.

Furthermore, State Industries prioritizes lifecycle analysis in the development of its products. This approach evaluates the environmental impact of a product from its conception through production, usage, and eventual disposal. By understanding the full lifecycle, State Industries can make informed decisions that enhance the sustainability of its offerings.

Consumer education is also a vital component of the Green Choice program. State Industries actively engages with customers to raise awareness about energy-efficient practices and the benefits of choosing sustainable products. By empowering consumers with knowledge, the initiative encourages responsible energy use and promotes a culture of sustainability.

In conclusion, State Industries Green Choice represents a holistic approach to manufacturing, focusing on energy efficiency, technological innovation, sustainable materials, and consumer engagement. This initiative not only helps to combat environmental issues but also fosters a market for eco-friendly products, paving the way for a more sustainable future. State Industries is setting a positive example in the industry by prioritizing ecological responsibility while delivering high-quality, efficient solutions to consumers.
Top Page Image Contents