State Industries Green Choice Optional Vertical and Horizontal Vent Kit Installation #4

Page 19

16.Collapse the 6” flue extension assembly as shown below. Install the O-ring end of the 3” (7.6 cm) extension approximately 1 1/4” (3.2 cm) into the end of the vent cap. If necessary, apply a soap solution to the O-ring to ease the assembly. Rotate the 3” extension clockwise until the other end is locked to the studs on the elbow.

20.Secure the 6” (15.2 cm) vent extension to the vent elbow with the two provided screws spacing them 180° apart.

FIGURE70.

Optional Vertical and Horizontal Vent Kit -

Installation #4

FIGURE66.

17.Using a # 22 drill bit, drill holes 180° apart at the connection point of the two 3” (7.6 cm) flue extensions. Secure with the two screws provided.

FIGURE67.

18. Expand the 6” (15.2 cm) telescoping extension to connect at the vent elbow.

 

If the vent hole has not been cut, refer to section, “Cutting The Opening

 

Through The Outside Wall.” See page 11.

 

1. First determine how far the vertical 3” (7.6 cm) diameter telescoping

 

flue sections are to be set and locked together with two screws

 

supplied.

FIGURE68.

 

19. Push the vent collar from the elbow against the wall and secure with

 

the four provided screws.

 

 

FIGURE 71.

 

Use the Chart #4, and figure 72 to determine the length of expansion of

 

the telescoping flue sections. Because of manufacturing tolerances, put

 

the telescoping extension on the water heater, adjust the height (dimen-

 

sion “X”) and mark the point. Once the length has been determined, lock

 

the two sections together by drilling two holes (180° apart) in the pipe

FIGURE69.

and secure with the supplied screws.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Residential Direct Vent GAS Water Heaters Important Definitions Safe INSTALLATION, USE and ServiceGeneral Safety Introduction Table of ContentsGET to Know Your Water Heater GAS Models Typical InstallationMixing Valve Usage Facts to Consider about the Location Locating the NEW Water HeaterVenting Clearances Combustion Air and VentilationFlue Extensions Optional Wire GrillHorizontal Extension Kit Chart #1Chart #2 Vertical Height Extension KitWater Heater Attitude ALL InstallationsStandard Vent Kit Installation #1 Cutting The Opening Through The Outside WallPage Page BTU’s in 1000’s NAT./L.P Chart #3 GAL CAPPage Page Optional Horizontal Vent Kit Installation #3 Page Through The Outside Wall. See Optional Vertical and Horizontal Vent Kit Installation #4Chart #4 GAL CAP Collar Optional Vent Cap Porcelain-Enameled Page Page Water Piping Installing the NEW Water HeaterValve and Pipe Insulation TEMPERATURE-PRESSURE Relief ValveFilling the Water Heater GAS Piping Sediment Traps GAS Piping with Flexible ConnectorGAS Piping with ALL Black Iron Pipe to GAS Control Before Lighting the Pilot Installation ChecklistPage Condensate Temperature RegulationFor Your Information Start UP ConditionsOperational Conditions Venting System Inspection Periodic MaintenanceBurner Cleaning GAS Control Valve & Burner AssemblyDraining TEMPERATURE-PRESSURE Relief Valve OperationHousekeeping Anode ROD InspectionLeakage Checkpoints Drain Valve Washer ReplacementRepair Parts List BTU’s in 1000’s NAT/L.P 36/36 38/38 40/40 48/44 55 NAT Parts GAL. CAP KEY # DescriptionRepair Parts List BTU’s in 1000’s NAT/L.P 36/36 38/38 40/40 48/44 This is a Repair Parts LIST, not a Packing ListTroubleshooting Guidelines Page Page

Green Choice specifications

State Industries Green Choice is a remarkable initiative designed to promote energy efficiency and environmentally-friendly practices in the manufacturing sector. The program focuses on providing high-efficiency appliances and heating systems that are not only cost-effective but also reduce environmental impact. With a growing concern about climate change, State Industries aims to address these issues through innovations in technology and sustainable practices.

One of the main features of the Green Choice initiative is its commitment to producing ENERGY STAR® certified products. These appliances meet strict energy efficiency guidelines set by the U.S. Environmental Protection Agency, helping consumers save money on energy bills while also decreasing their carbon footprint. By prioritizing energy efficiency, State Industries ensures that their products move the industry toward a more sustainable future.

Incorporating advanced technologies is central to the Green Choice initiative. The use of state-of-the-art insulation materials minimizes heat loss, while high-efficiency burners and heat exchangers maximize energy utilization in heating systems. These technological innovations lead to significant reductions in energy consumption, translating to both financial savings for consumers and reduced greenhouse gas emissions.

Another characteristic of Green Choice is the emphasis on using sustainable materials in manufacturing. State Industries strives to source materials that are either recyclable or derived from renewable resources. This commitment not only supports the economy but also minimizes waste and environmental degradation associated with traditional manufacturing processes.

Furthermore, State Industries prioritizes lifecycle analysis in the development of its products. This approach evaluates the environmental impact of a product from its conception through production, usage, and eventual disposal. By understanding the full lifecycle, State Industries can make informed decisions that enhance the sustainability of its offerings.

Consumer education is also a vital component of the Green Choice program. State Industries actively engages with customers to raise awareness about energy-efficient practices and the benefits of choosing sustainable products. By empowering consumers with knowledge, the initiative encourages responsible energy use and promotes a culture of sustainability.

In conclusion, State Industries Green Choice represents a holistic approach to manufacturing, focusing on energy efficiency, technological innovation, sustainable materials, and consumer engagement. This initiative not only helps to combat environmental issues but also fosters a market for eco-friendly products, paving the way for a more sustainable future. State Industries is setting a positive example in the industry by prioritizing ecological responsibility while delivering high-quality, efficient solutions to consumers.
Top Page Image Contents