State Industries Green Choice instruction manual Chart #4 GAL CAP

Page 20

5.Place the 6” (15.2 cm) vent section over the 3” (7.6 cm) flue section. Subtract 3/4” (1.9 cm) from the predetermined “X” dimension. This determines the length of the 6” (15.2 cm) vent extension. Slide the 6” (15.2 cm) vent extension apart to this dimension and secure with the two screws supplied.

FIGURE72.

CHART #4.

*GAL CAP

*BTU’s in 1000’s - NAT./L.P.

 

A

40

36/36

48 3/4”

 

124 cm

50

38/38

57 1/2”

 

146 cm

40

40/40

48 3/4”

 

124 cm

50

48/44

61”

 

155 cm

75

55 NAT.

63”

 

160 cm

*Check the model and rating plate attached to the water heater for specific model number and other detailed information.

2.Set the vertical 3” (7.6cm)diameter telescoping flue section in place on the flue collar. Using a #22 drill bit, drill two holes (180°apart) and secure the vertical assembly to the flue collar with the two supplied screws.

FIGURE76.

6.Form the round end of the 6” (15.2 cm) vent extension to the top of the jacket and secure with four sheet metal screws.

FIGURE73.

3.Slide the 6” (15.2 cm) vent telescoping section apart to reveal the beads. Fill the beads using the supplied caulking.

FIGURE74.

4. Apply an ample amount of sealant around the oval flare of the jacket.

FIGURE75.

FIGURE 77.

7.Place the 3” (7.6 cm) elbow on the flue extension. Align the elbow to the hole previously made in the outside wall. Using the slots in the elbow, mark the 3” (7.6 cm) diameter end of the flue extension. Using a #22 drill bit, drill two holes into the flue extension and secure with the two provided sheet metal screws.

FIGURE78.

NOTE: the standard kit includes a 3” (7.6 cm) flue extension and a 6” (15.2 cm) elbow extension. These parts will not be used with the horizontal kit.

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Residential Direct Vent GAS Water Heaters Safe INSTALLATION, USE and Service Important DefinitionsGeneral Safety Table of Contents IntroductionTypical Installation GET to Know Your Water Heater GAS ModelsMixing Valve Usage Locating the NEW Water Heater Facts to Consider about the LocationCombustion Air and Ventilation Venting ClearancesOptional Wire Grill Flue ExtensionsChart #1 Chart #2Vertical Height Extension Kit Horizontal Extension KitALL Installations Standard Vent Kit Installation #1Cutting The Opening Through The Outside Wall Water Heater AttitudePage Page Chart #3 GAL CAP BTU’s in 1000’s NAT./L.PPage Page Optional Horizontal Vent Kit Installation #3 Page Optional Vertical and Horizontal Vent Kit Installation #4 Through The Outside Wall. SeeChart #4 GAL CAP Collar Optional Vent Cap Porcelain-Enameled Page Page Installing the NEW Water Heater Water PipingTEMPERATURE-PRESSURE Relief Valve Valve and Pipe InsulationFilling the Water Heater GAS Piping GAS Piping with ALL Black Iron Pipe to GAS Control GAS Piping with Flexible ConnectorSediment Traps Installation Checklist Before Lighting the PilotPage Temperature Regulation For Your InformationStart UP Conditions CondensateOperational Conditions Periodic Maintenance Burner CleaningGAS Control Valve & Burner Assembly Venting System InspectionTEMPERATURE-PRESSURE Relief Valve Operation HousekeepingAnode ROD Inspection DrainingDrain Valve Washer Replacement Leakage CheckpointsRepair Parts List Parts GAL. CAP KEY # Description BTU’s in 1000’s NAT/L.P 36/36 38/38 40/40 48/44 55 NATRepair Parts List This is a Repair Parts LIST, not a Packing List BTU’s in 1000’s NAT/L.P 36/36 38/38 40/40 48/44Troubleshooting Guidelines Page Page

Green Choice specifications

State Industries Green Choice is a remarkable initiative designed to promote energy efficiency and environmentally-friendly practices in the manufacturing sector. The program focuses on providing high-efficiency appliances and heating systems that are not only cost-effective but also reduce environmental impact. With a growing concern about climate change, State Industries aims to address these issues through innovations in technology and sustainable practices.

One of the main features of the Green Choice initiative is its commitment to producing ENERGY STAR® certified products. These appliances meet strict energy efficiency guidelines set by the U.S. Environmental Protection Agency, helping consumers save money on energy bills while also decreasing their carbon footprint. By prioritizing energy efficiency, State Industries ensures that their products move the industry toward a more sustainable future.

Incorporating advanced technologies is central to the Green Choice initiative. The use of state-of-the-art insulation materials minimizes heat loss, while high-efficiency burners and heat exchangers maximize energy utilization in heating systems. These technological innovations lead to significant reductions in energy consumption, translating to both financial savings for consumers and reduced greenhouse gas emissions.

Another characteristic of Green Choice is the emphasis on using sustainable materials in manufacturing. State Industries strives to source materials that are either recyclable or derived from renewable resources. This commitment not only supports the economy but also minimizes waste and environmental degradation associated with traditional manufacturing processes.

Furthermore, State Industries prioritizes lifecycle analysis in the development of its products. This approach evaluates the environmental impact of a product from its conception through production, usage, and eventual disposal. By understanding the full lifecycle, State Industries can make informed decisions that enhance the sustainability of its offerings.

Consumer education is also a vital component of the Green Choice program. State Industries actively engages with customers to raise awareness about energy-efficient practices and the benefits of choosing sustainable products. By empowering consumers with knowledge, the initiative encourages responsible energy use and promotes a culture of sustainability.

In conclusion, State Industries Green Choice represents a holistic approach to manufacturing, focusing on energy efficiency, technological innovation, sustainable materials, and consumer engagement. This initiative not only helps to combat environmental issues but also fosters a market for eco-friendly products, paving the way for a more sustainable future. State Industries is setting a positive example in the industry by prioritizing ecological responsibility while delivering high-quality, efficient solutions to consumers.
Top Page Image Contents