RIDGID 1822-I manual Operation Instructions Using Geared Threaders, Adjusting No Geared Threader

Page 17

1822-I Pipe and Bolt Threading Machine

Operation Instructions Using Geared Threaders

WARNING

Do not wear gloves or loose clothing when oper- ating Threading Machine. Keep sleeves and jack- ets buttoned. Do not reach across the machine or geared threader.

Do not use this Threading Machine if the foot switch is broken or missing. Always wear eye protection to protect eyes from dirt and other for- eign objects.

To prevent tipping, proper set-up of the Threading Machine and Geared Threader is required. Follow instructions carefully.

No. 141 Geared Threader weighs 95 pounds. Two

(2) persons should be used to lift this threader.

Adjusting No. 141 Geared Threader

1.With the No. 141 Geared Threader on floor and drive shaft facing up, pull two cam plate knobs and rotate cam plate to desired size. Locating pins will drop into holes in selector plate.

Thread Size Adjustment

1.For standard thread depth, hold workholder stationary and rotate gear case by hand until standard line on pinion sleeve is flush with bottom of die head or the standard line on guide post is flush with top of die head (Figure 18).

2.For oversized threads, rotate gear case until the 2T Over Line on guide post is flush with top of die head.

3.For undersized threads, rotate gear case until the 2T Under Line on guide post is flush with top of die head.

 

Guide Post

Reference

Head

 

Lines (3)

 

Drive Shaft

Cam Plate

 

Knob (2)

Clamp Screw

 

Figure 18 – No. 141 Geared Threader with Drive Shaft Up

Selector

Die HeadPlateDie (Set of 5) Guide

Block

2T Under

StopLine

Screw

Standard

Red StopLIne

Line

2T Over

StandardLine

Line

 

Guide Post

Pinion

 

Sleeve

Screw

 

Gear Case

Figure 19 – No. 141 Geared Threader showing Pinion Sleeve and Guide Post Reference Lines

Indexing Guide Post For Straight Or Tapered Threads

(Figure 19)

1.At a standard size thread setting, remove set screw at base of guide post and pull post through die head.

2.For tapered threads, insert guide post with the di- agonal slot inward through die head. Guide block will engage diagonal slot and post will rotate toward gear case.

Ridge Tool Company

15

Page 16 Page 18
Image 17
Page 16 Page 18
Contents 1822-I Table of Contents 1822-I Pipe and Bolt Threading Machine Work Area Safety General Safety InformationElectrical Safety Personal SafetyService Specific Safety InformationMachine Safety Tool Use and CareSpecifications Description, Specifications and Standard EquipmentAccessories DescriptionDie Heads and Dies Machine AssemblyMachine Stands Mounting Machine to Universal StandsPosition stand stop bracket so that the end Mounting Machine to No Folding Wheel Stand Installing No Oil Pan CoverMounting Machine To Bench Transporting Machine with No StandSling Transportation Machine InspectionMachine and Work Area Set-Up Installing and Chucking Pipe In Threading Machine Operation Using Machine-Mounted ToolsCutting Pipe with No Cutter View AngleTrigger Assembly Speed Selection ChartReaming Pipe with No Reamer Reamer HandwheelRemoving Pipe From The Threading Machine Installing Dies In Self-Opening Die Head Right Hand OnlyRoll Pin Size Bar Index Line Lock Screw TriggerChecking Thread Length Installing Die In Model 816/817 Die HeadsWasher Index Line Head Link Size Stop Handle Plunger KnobNo Nipple Chuck and No Adapter Kit InstallationNipple Threading Procedure Adjusting No Geared Threader Operation Instructions Using Geared ThreadersThread Size Adjustment Indexing Guide Post For Straight Or Tapered ThreadsChanging Dies Installing No Geared Threader FigureOperating No Geared Threader Threading 21/2″ to 4″ Pipe 45 RPMNo Blade Cutter and No Adapter Kit Installation of No Blade CutterLeft Hand Machine Operation Positioning Front Jaws for Left Hand OperationAccessories For Threading Machine AccessoriesPositioning Rear Centering Jaws for Left Hand Operation Oil Line Set-Up for Left Hand OperationAccessories For Threading By Close-Coupled Method Maintenance InstructionsOil System Maintenance Front Jaw Insert and Centering Finger ReplacementSpindle Assembly Removal Rear Centering Finger/Jaw ReplacementSpindle Assembly Installation Spindle Conversion Kit for Plastic Coated PipeStep Machine StorageService and Repair Wiring Diagrams Pipe and Bolt Threading Machine Machine à fileter 1822-I pour tuyaux et boulons Consignes générales de sécurité Table des matièresSécurité du chantier Consignes générales de sécuritéSécurité électrique Sécurité personnelleMise EN Garde Sécurité de la pédale de commande Service après-venteConsignes de sécurité particulières Utilisation et entretien de l’appareilEquipements de base Description, spécifications et équipements de baseSpécifications Machine de base AccessoiresTêtes de filières et filières Supports d’embase Assemblage de la machineMontage de la machine sur support universel Modèle DescriptionMontage de la machine sur support pliant sur roues n Installation du couvercle de carter d’huileRallonge d’arrivée Filtre à huile Raccord coudé PousserTransport de la machine sur support n Inspection de la machineMontage de la machine sur établi Machine à fileter Préparation de la machine et du chantierUtilisation des outils incorporés de la machine Angle de vue Coupe des tuyaux à l’aide du coupe-tubes nAlésage des tuyaux à l’aide de l’alésoir n Alésoir Volant Tableau de sélection de régimeMatériau et Ø DétenteRetrait des tuyaux de la machine à fileter Levier de verrouillage Trigger AssemblyRondelle Repère Tête Taquet Tête de filière universelle à ouverture rapideFiletage des raccords Mandrin à raccords n 819 et ensemble adaptateur nVérification de la longueur de filetage Réglage de la fileteuse démultipliée n Réglage des dimensions de filetageUtilisation des fileteuses démultipliées Installation de la fileteuse démultipliée n 141 Figure Remplacement des filièresBarre d’indexage pour filetages cylindriques et coniques Utilisation de la fileteuse démultipliée nFiletage des tuyaux de 21/2″ à 4″ 45 t/min Installation du coupe-tubes à lame nCoupe-tubes à lame n 821 et ensemble adaptateur n Positionnement des mâchoires avant pour rotation à gauche Inversion du sens de rotation rotation à gaucheAccessoires pour filetages des raccords à couplage direct AccessoiresAccessoires pour machine à fileter EntretienPoints de Lubrification Logement d’axe Remplacement du doigt de centrage arrière et de la mâchoireLubrification de la machine Ensemble de conversion de fuseau pour tuyaux plastifiés Installation du fuseauRetrait du fuseau 1ère étapeStockage de la machine Service après-vente et réparationsSchéma électrique Machine à fileter 1822-I pour tuyaux et boulons Máquina Roscadora de tubos Montaje de la máquina ÍndiceSeguridad en la zona de trabajo Información general de seguridadSeguridad eléctrica Seguridad personalUso y cuidado de la máquina Información específica de seguridadServicio Advertencia Seguridad del interruptor De pieSeguridad de la máquina Descripción, especificaciones y equipo estándarDescripción EspecificacionesAccesorios Montaje de la máquinaEquipo estándar Soportes para la máquinaCabezales de terrajas y Terrajas Detalle Montaje de la máquina sobre el soporte universalInstalación de la cubierta de la bandeja de aceite No.1460 Transporte de la máquina montada en un Soporte No Montaje de la máquina sobre una mesa de trabajoFigura 6 Transporte con eslinga Revisión de la máquinaPreparación de la máquina y de la zona de trabajo Corte de tubos con el cortatubos No Empleo de herramientas montadas a la máquinaInstalación y sujeción del tubo en la Roscadora Volante Escariado de tubos con el escariador NoÁngulo de visión Cortadora Escariador Tabla de selección de velocidades Extracción del tuboRpm recomendadas GatilloFigura 11 Cabezal de terrajas universal de auto-apertura Pasador Barra dimensionalLínea marcada Arandela Cabezal Enlace Verificación de la longitud de la roscaPalanca de AgarreInstalación Mandril Niplero No y kit de adaptación NoProcedimiento para roscar niples Regulación del tamaño de la rosca Regulación de la Roscadora a Engranajes NoInstalación de la Roscadora a Engranajes No Cambio de terrajasFuncionamiento de la Roscadora a Engranajes No Instalación del cortatubos de cuchilla No Cortatubos de cuchilla No y kit de adaptación NoRoscado de tubos de 21/2 hasta 4 pulgadas 45 rpm Funcionamiento de la máquina a mano izquierda Accesorios para la Máquina Roscadora AccesoriosAccesorios que van acoplados directamente a la máquina SoportesMantenimiento del sistema de lubricación Instrucciones de mantenimientoLubricación del rodamiento del árbol Recambio de la mordaza delantera y de la uña de centradoInstalación del árbol Recambio de la mordaza trasera y de la uña de centradoExtracción del árbol Primer paso Segundo paso Tercer paso Almacenamiento de la máquinaServicio y reparaciones 240V 60Hz 10A Diagrama de cableadoHow you can get service What is coveredWhat we will do to correct problems What is not covered

1822-I specifications

The RIDGID 1822-I is a powerful and versatile compact pipe threading machine that is widely recognized for its reliability and innovative design. This electric threading machine is specifically engineered for both professional and DIY users, ensuring high productivity in pipe fitting and fabrication tasks.

At the core of its engineering, the RIDGID 1822-I features a robust motor that delivers high torque, allowing for efficient threading of a variety of pipe sizes up to 2 inches in diameter. This machine is equipped with a quick-release pipe clamp that securely holds the workpiece in place, providing enhanced stability and safety during operations. The user-friendly controls enable seamless operation with minimal setup time, making it an ideal choice for contractors and plumbing professionals.

One of the standout technologies integrated into the RIDGID 1822-I is its automatic shut-off feature that enhances safety while prolonging the lifespan of the machine. It also boasts an adjustable threading stop, allowing operators to maintain consistent thread lengths and ensuring precision in their work. This machine is compact in design, enabling easy portability and storage, which is especially beneficial for jobs in confined spaces or on construction sites.

The RIDGID 1822-I is constructed using durable materials and comes with a sturdy frame that minimizes vibration, significantly reducing user fatigue during extended use. Additionally, it features an integrated oil reservoir that simplifies the process of threading pipes, ensuring proper lubrication and ensuring smoother cuts.

Another characteristic that sets the RIDGID 1822-I apart is its versatility. It is compatible with various RIDGID threading dies and accessories, allowing for customization based on the specific requirements of each job. Furthermore, the machine's exceptional threading speed leads to increased efficiency, enabling users to complete projects more quickly without compromising on quality.

In conclusion, the RIDGID 1822-I is an indispensable tool for professionals looking for a reliable, efficient, and versatile pipe threading solution. Its combination of advanced features, durability, and user-friendly design make it a top choice for those in the plumbing and construction industries, as well as for DIY enthusiasts seeking a dependable machine for their pipe threading needs. With the RIDGID 1822-I, users can achieve high-quality results with ease and confidence.
Top Page Image Contents