RIDGID 1210 manual Machine and Work Area Set-Up, Filling Coolant Reservoir

Page 8

1210 Oil-less Threading Machine

ing, misaligned or binding parts as well as any other conditions which may affect the safe and normal op- eration of the machine. If any of these conditions are present, do not use the Threading Machine until any problem has been repaired.

7.Use tools and accessories that are specifically de- signed for your Threading Machine and meet the needs of your application. The correct tools and ac- cessories allow you to do the job successfully and safely. Accessories suitable for use with other equip- ment may be hazardous when used with this Threading Machine.

8.Clean any oil, grease or dirt from all handles and controls. This reduces the risk of injury due to a tool or control slipping from your grip.

9.Inspect the cutting edges of your tools and dies. If necessary, have them replaced prior to using the Threading Machine.

NOTE! Use sharp dies at all times. Dull dies require more power from the motor and produce poor quality threads.

10.Clean metal shavings and other debris from the chip tray.

Machine and Work Area Set-Up

WARNING

2.Clean up the work area prior to setting up any equip- ment.

3.If the workpiece extends more than four (4) feet beyond the Threading Machine, use one or more pipe stands to prevent tipping and the oscillation of the pipe.

4.Check level of RIDGID Threading Cutting Coolant and fill as necessary.

NOTE! RIDGID Thread Cutting Coolant is engineered specifically for use with the 1210 Threading Machine. It is designed to quickly cool the pipe and leave a clean, dry thread ready for imme- diate installation.

Observe coolant level in the reservoir by view- ing the sight glass at the rear of the Model 1210 (Figure 4).

Unscrew the reservoir cap and pour the coolant into the reservoir (Figure 4).

NOTE! Reservoir will hold approximately 16 oz. of fluid.

• Replace the reservoir cap.

CAUTION Use of fluids other than RIDGID Thread Cutting Coolant will void the RIDGID 1210 warranty and may cause damage to the threading machine and thread- ing dies. RIDGID Thread Cutting Coolant should NOT be used in or with any other RIDGID threading equipment.

To prevent serious injury, proper set-up of the machine and work area is required. The following procedures should be followed to set-up the ma- chine:

1.Locate a work area that has the following:

Adequate lighting

No flammable liquids, vapors or dust that may ignite.

Grounded electrical outlet

Clear path to the electrical outlet that does not contain any sources of heat or oil, sharp edges or moving parts that may damage electrical cord.

Dry place for machine and operator. Do not use the machine while standing in water.

Level ground

Adequate ventilation to prevent accumulation of coolant vapors

Sight

Glass

Figure 4 – Filling Coolant Reservoir

6

Ridge Tool Company

Image 8
Contents Machine Table of Contents 1210 General Safety Information Work Area SafetyElectrical Safety Personal SafetySpecific Safety Information ServiceMachine Safety Tool Use and CareDescription, Specifications and Standard Equipment Machine AssemblySpecifications DescriptionMachine Inspection Mounting On The No StandMachine and Work Area Set-Up Filling Coolant ReservoirPriming The Coolant System Full Coolant ReservoirCutting Pipe with No Cutter Installing Pipe In Threading MachineOperating Instructions Reaming Pipe with No Reamer Threading Pipe with No Die HeadTransporting Machine Threading Pipe with No a Self-Opening Die HeadRemoving Pipe From The Machine Replace die head in machine Accessories Checking Thread LengthMaintenance Instructions Jaw ReplacementMachine Storage Replacing Carbon BrushesService and Repair Wiring Diagrams 120V 60 Hz 230V Europe 110V UK 100V Japan 230V ExportOil-less Threading Machine Machine à Fileter Sans Huile Modèle Table des Matières Consignes Générales de SécuritéConsignes générales de sécurité Sécurité du chantierSécurité électrique Sécurité personnelleMise EN Garde Sécurité de la pédale de commande Consignes de sécurité spécifiquesUtilisation et entretien de l’appareil RéparationsSpécifications Description, Spécifications et Accessoires de BaseAccessoires de base Assemblage de la Machine Montage sur support NInspection de la Machine Préparation de la Machine et du ChantierRemplissage du réservoir de liquide de refroidissement Amorçage du système de refroidissement Event du réservoir ouvertCoupe des tuyaux à l’aide du coupe- tubes N Mode d’EmploiInstallation et mandrinage des tuyaux Alésage des tuyaux à l’aide de l’alésoir N Filetage des tuyaux à l’aide de la tête de filière NRetrait des tuyaux de la machine Filetage des tuyaux à l’aide de la tête de filière NTransport de la machine Modèle 1210 et support N 120 prêts à être transportésVérification de la longueur des filetages Accessoires Remplacement des mâchoiresRemplacement des balais au carbone EntretienStockage de la Machine Entretien et RéparationsSchéma Electrique 120V 60 Hz230V Europe 110V RU 100V Japon 230V ExportMachine à fileter sans huile Modèle 1210 Máquina Roscadora Seca sin aceite Indice Información general de seguridadInformación general de seguridad Seguridad en la zona de trabajoSeguridad eléctrica Seguridad personalInformación específica de seguridad Uso y cuidado de la herramientaServicio Advertencia Seguridad del Interruptor De PieDescripción, especificaciones y equipo estándar DescripciónEspecificaciones Equipo estándarMontaje de la máquina Montaje sobre el Soporte NoRevisión de la máquina Preparación de la máquina y de la zona de trabajoFigura 4 Modo de llenar el depósito de refrigerante Instrucciones de funcionamiento Cómo cebar el sistema refrigeranteEscariado de tubos con la Escariadora No Instalación del tubo en la RoscadoraCorte de tubos con la Cortadora No Roscado de tubos con un Cabezal de Terrajas No Figura 9 Escariado de un tubo con la Escariadora NoCómo sacar el tubo de la Roscadora Transporte de la máquinaFigura 14 Cabezal de Terrajas Universal de Apertura Rápida Verificación de la longitud de una rosca Ancho total de la roscaAccesorios Instrucciones para el mantenimientoRecambio de las piezas de la mordaza Recambio de las escobillas de carbonoAlmacenamiento de la máquina Servicio y reparacionesJapón Exportación Diagrama de cableadoEuropa 230V Reina Unido 1210 Máquina Roscadora Seca sin aceite Ridge Tool Company
Related manuals
Manual 2 pages 33.7 Kb

1210 specifications

The RIDGID 1210 is an exceptional piece of equipment tailored for plumbing and pipefitting professionals. This compact yet powerful machine provides unparalleled reliability and performance, making it a staple in any contractor's toolkit. Designed to tackle some of the toughest jobs in the field, the RIDGID 1210 combines innovative technology with robust construction to ensure that it meets the demanding needs of users.

One of the standout features of the RIDGID 1210 is its advanced threading system. It boasts a 3-in-1 threading capability that allows users to thread various pipe sizes and materials with ease, including steel, iron, and PVC. This flexibility enhances productivity, as contractors can switch between different tasks without the need for multiple tools.

The machine is powered by a high-torque motor that delivers consistent performance even during heavy-duty applications. This ensures that users can complete their threading tasks with speed and precision. Moreover, the RIDGID 1210 is equipped with a self-oiling system, which significantly reduces maintenance time by keeping critical components lubricated and operating smoothly.

Portability is another key characteristic of the RIDGID 1210. Its lightweight design, coupled with ergonomic handles, allows for easy transport and maneuverability on job sites. This means crews can easily take the machine to various locations, enhancing their efficiency and reducing downtime.

The RIDGID 1210 also prioritizes user safety. It comes with built-in safety features, such as an emergency stop button and protective shields, which protect the user from rotating parts and debris. The thoughtful design extends to its user-friendly controls, which provide intuitive operation, making it accessible even for those who are new to threading machinery.

Furthermore, the RIDGID brand is synonymous with durability and quality. The 1210 is constructed from heavy-duty materials designed to withstand the rigors of both indoor and outdoor job sites. This robustness ensures that it remains a reliable investment for contractors looking for a long-lasting threading solution.

Overall, the RIDGID 1210 is a well-rounded threading machine that combines technology, durability, and user-centric design to deliver outstanding performance. Its versatility, power, and portability make it an essential tool for plumbing and pipefitting professionals, providing them with the capabilities they need to succeed in their projects. Whether you are a seasoned contractor or an aspiring plumber, the RIDGID 1210 is poised to become an invaluable ally in your work.