RIDGID 1210 manual Replace die head in machine

Page 13

1210 Oil-less Threading Machine

Figure 13 – Foot Switch In Carrying Position

Installing Dies and Adjusting For Size In No. 610 Quick-Opening Die Head

NOTE! The universal die head (Figure 14) for right hand threads requires two sets of dies to thread pipe ranging from 1/2″ through 1″ . One set of dies is required for each of the following pipe size ranges: (1/2″ - 3/4″ ) and (1″ ).

1.With machine unplugged, remove die head.

2.Lay die head on bench with numbers up.

3.Flip throwout lever to OPEN position.

4.Loosen clamp lever approximately three full turns.

5.Lift tongue of clamp lever washer up out of slot under size bar. Slide throwout lever all the way to the end of slot in the OVER direction on size bar (CHANGE DIES arrow on rear of cam plate).

6.Remove worn dies from die head.

7.Insert new dies to indicator line. Die numbers 1 through 4 on the dies must agree with those on the die head.

8.Slide throwout lever back so that tongue of clamp lever washer will drop in slot under size bar.

9.Adjust die head size bar until index line on link is aligned with proper size mark on size bar.

10.Tighten clamp lever.

NOTE! If oversize or undersize threads are required, set the index line in direction of OVER or UNDER size mark on size bar.

Washer

Index Line

 

Head

Link

 

Throwout

Clamp Lever

Lever

 

 

Size Bar

Figure 14 – No. 610 Quick-Opening Die Head

11. Replace die head in machine.

Installing Dies and Adjusting For Size In No. 610A Auto-Opening Die Head

NOTE! The universal die head (Figure 11) for right hand threads requires two sets of dies to thread pipe ranging from 1/2″ through 1″ . One set of dies is required for each of the following pipe size ranges: (1/2″ - 3/4″ ) and (1″ ).

1.With machine unplugged, remove die head.

2.Push cocking lever forward until the trigger cocks (Figure 11).

3.Lay die head down on flat surface with die head num- bers facing up.

4.Release toggle knob as shown (Figure 15).

Figure 15 – Release Toggle Knob By Pressing In Direction of Arrow

5.Rotate die head in clockwise direction until toggle knob reaches end of size bar. Toggle knob must not be allowed to engage the size blocks while rotating die

Ridge Tool Company

11

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Machine Table of Contents 1210 Work Area Safety General Safety InformationElectrical Safety Personal SafetyService Specific Safety InformationMachine Safety Tool Use and CareMachine Assembly Description, Specifications and Standard EquipmentSpecifications DescriptionMounting On The No Stand Machine InspectionFilling Coolant Reservoir Machine and Work Area Set-UpFull Coolant Reservoir Priming The Coolant SystemOperating Instructions Installing Pipe In Threading MachineCutting Pipe with No Cutter Threading Pipe with No Die Head Reaming Pipe with No ReamerRemoving Pipe From The Machine Threading Pipe with No a Self-Opening Die HeadTransporting Machine Replace die head in machine Checking Thread Length AccessoriesJaw Replacement Maintenance InstructionsMachine Storage Replacing Carbon BrushesService and Repair 120V 60 Hz 230V Europe 110V UK 100V Japan 230V Export Wiring DiagramsOil-less Threading Machine Machine à Fileter Sans Huile Modèle Consignes Générales de Sécurité Table des MatièresSécurité du chantier Consignes générales de sécuritéSécurité électrique Sécurité personnelleConsignes de sécurité spécifiques Mise EN Garde Sécurité de la pédale de commandeUtilisation et entretien de l’appareil RéparationsAccessoires de base Description, Spécifications et Accessoires de BaseSpécifications Montage sur support N Assemblage de la MachinePréparation de la Machine et du Chantier Inspection de la MachineRemplissage du réservoir de liquide de refroidissement Event du réservoir ouvert Amorçage du système de refroidissementInstallation et mandrinage des tuyaux Mode d’EmploiCoupe des tuyaux à l’aide du coupe- tubes N Filetage des tuyaux à l’aide de la tête de filière N Alésage des tuyaux à l’aide de l’alésoir NFiletage des tuyaux à l’aide de la tête de filière N Retrait des tuyaux de la machineModèle 1210 et support N 120 prêts à être transportés Transport de la machineVérification de la longueur des filetages Remplacement des mâchoires AccessoiresRemplacement des balais au carbone EntretienEntretien et Réparations Stockage de la Machine120V 60 Hz Schéma Electrique230V Europe 110V RU 100V Japon 230V ExportMachine à fileter sans huile Modèle 1210 Máquina Roscadora Seca sin aceite Información general de seguridad IndiceSeguridad en la zona de trabajo Información general de seguridadSeguridad eléctrica Seguridad personalUso y cuidado de la herramienta Información específica de seguridadServicio Advertencia Seguridad del Interruptor De PieDescripción Descripción, especificaciones y equipo estándarEspecificaciones Equipo estándarMontaje sobre el Soporte No Montaje de la máquinaPreparación de la máquina y de la zona de trabajo Revisión de la máquinaFigura 4 Modo de llenar el depósito de refrigerante Cómo cebar el sistema refrigerante Instrucciones de funcionamientoCorte de tubos con la Cortadora No Instalación del tubo en la RoscadoraEscariado de tubos con la Escariadora No Figura 9 Escariado de un tubo con la Escariadora No Roscado de tubos con un Cabezal de Terrajas NoTransporte de la máquina Cómo sacar el tubo de la RoscadoraFigura 14 Cabezal de Terrajas Universal de Apertura Rápida Ancho total de la rosca Verificación de la longitud de una roscaInstrucciones para el mantenimiento AccesoriosRecambio de las piezas de la mordaza Recambio de las escobillas de carbonoServicio y reparaciones Almacenamiento de la máquinaEuropa 230V Reina Unido Diagrama de cableadoJapón Exportación 1210 Máquina Roscadora Seca sin aceite Ridge Tool Company
Related manuals
Manual 2 pages 33.7 Kb

1210 specifications

The RIDGID 1210 is an exceptional piece of equipment tailored for plumbing and pipefitting professionals. This compact yet powerful machine provides unparalleled reliability and performance, making it a staple in any contractor's toolkit. Designed to tackle some of the toughest jobs in the field, the RIDGID 1210 combines innovative technology with robust construction to ensure that it meets the demanding needs of users.

One of the standout features of the RIDGID 1210 is its advanced threading system. It boasts a 3-in-1 threading capability that allows users to thread various pipe sizes and materials with ease, including steel, iron, and PVC. This flexibility enhances productivity, as contractors can switch between different tasks without the need for multiple tools.

The machine is powered by a high-torque motor that delivers consistent performance even during heavy-duty applications. This ensures that users can complete their threading tasks with speed and precision. Moreover, the RIDGID 1210 is equipped with a self-oiling system, which significantly reduces maintenance time by keeping critical components lubricated and operating smoothly.

Portability is another key characteristic of the RIDGID 1210. Its lightweight design, coupled with ergonomic handles, allows for easy transport and maneuverability on job sites. This means crews can easily take the machine to various locations, enhancing their efficiency and reducing downtime.

The RIDGID 1210 also prioritizes user safety. It comes with built-in safety features, such as an emergency stop button and protective shields, which protect the user from rotating parts and debris. The thoughtful design extends to its user-friendly controls, which provide intuitive operation, making it accessible even for those who are new to threading machinery.

Furthermore, the RIDGID brand is synonymous with durability and quality. The 1210 is constructed from heavy-duty materials designed to withstand the rigors of both indoor and outdoor job sites. This robustness ensures that it remains a reliable investment for contractors looking for a long-lasting threading solution.

Overall, the RIDGID 1210 is a well-rounded threading machine that combines technology, durability, and user-centric design to deliver outstanding performance. Its versatility, power, and portability make it an essential tool for plumbing and pipefitting professionals, providing them with the capabilities they need to succeed in their projects. Whether you are a seasoned contractor or an aspiring plumber, the RIDGID 1210 is poised to become an invaluable ally in your work.
Top Page Image Contents