Fostex CR300 Wireless remote control, Parallel remote control, Name on the main unit See

Page 14

CONTROLS AND INDICATORS

REMOTE CONTROL UNIT

● Wireless remote control	Operations performed by buttons marked "❋" can
	also be carried out by using buttons with the same
	name on the main unit (See page 12).

❋Record buttons

				(REC)
MODEL 8317				NOTE: For recording,
REC				press the 2 buttons simultaneously
				press the 2 buttons simultaneously

		TRACK NO.		❋ Manual TRACK NO.
	FADER	TRACK NO.		WRITE button
FADER button		WREITE		WRITE button	Acceptance of commands from
		WREITE

				❋ Record muting button	the wireless remote controller
				❋ Record muting button	by the CR300 can be set using
					by the CR300 can be set using
PEPEAT button	REPEAT				the MENU button function.
PEPEAT button				❋ Manual search button	(See page 24)
				❋ Manual search button
				❋ Track search button
	1	2	3	❋ Stop button
	1	2	3	❋ Pause button
Numeric buttons				❋ Pause button
Numeric buttons	4	5	6	❋ Play button
(1 to 10, >10)	4	5	6
(1 to 10, >10)
	7	8	9

Program button

(PGM)

Program check button

(CHECK)

10 10 TIME

PGM CHECK CLEAR

❋Time button (TIME)

❋Program clear button (CLEAR)

Remote control sensor Point the remote control unit and press its buttons.

30

30

●Parallel remote control

The CR300 can be controlled through the rear panel parallel remote control input connector and also with the wireless remote controller included with the CR300.

7m(23 ft)

Remote controllable range

DIN 8 pin connector

PARALLEL

REMOTE

The CR300 can be controlled with external switches by utilizing the circuit shown below.

		7		6
GND	WRITENO	3	8	1
GND	WRITENO	5	2	4
			2	Not Use
				Not Use
PLAY	MANUAL TRACK			PAUSE	REC	STOP

Caution on the remote control operation

•Remote control might not work if there is an obstacle between the remote control unit and the CR300 or if the remote control unit is operated at too great of an angle from the remote control sensor.

•Erroneous operation may occur in strong light such as direct sunlight or fluorescent lamp light shining into the remote control sensor.

•The CR300 may operate erroneously if it is used near equipment radiating infrared rays or if the infrared remote control unit of other equipment is used near the CR300. On the contrary, if this remote control unit is operated near another piece of equipment which can be controlled with infrared rays, that equipment might not work correctly.

•Replace batteries when the remote controllable range decreases noticeably.

14

CR300 <PRB1291-B>

Image 14

Contents CR300 Safety Instructions Pour le modele Canadien Information to UserFor Canadian model Features Contents Battery loading method Checking AccessoriesAC power cord AAA/R03 dry cell batteries ... x Batteries AAA/R03 dry cell batteriesCD lens cleaner Precautions regarding installationCleaning the compact disc recorder LocationCD-R finalization DiscsDiscs usable with this unit CD-R and CD-RW discsDo not play a CD with a special shape Disc maintenanceHandling of disc Disc storageDigital Signal Connection ConnectionsAnalog Signal Connection Controls and Indicators Switching the time display Also be carried out by using buttons with the same Wireless remote controlParallel remote control Operations performed by buttons marked can2,4 Turn the power onDisc LOADING/UNLOADING Open the disc trayRecording a CD, DAT, MD or DCC source S/P DIF only Mode of RecordingTrack numbers are updated automatically by this unit Recording of other-than-audio signals Recording from the middle of a discTrack recording RW disc containing Recordable space All-track recordingLoad a CD-R or CD Press the Finalize Automatic finalization recordingSynchro button twice ButtonAfter recording, press the stop button to end recording Manual DIGITAL-SOURCE RecordingPress the Record REC buttons ANALOG-SOURCE Recording Press the pause Or play button Record-pause modeAdjust the recording level RW disc containing a Recordable spaceLevel meter Recording level adjustmentAdjustment reference Minimum recording time per trackFade In / Fade Out Time Setting Copy Bit SettingAuto stop delay time Setting in Digital Synchro Menu Button FunctionsBalanced Output Level Setting Automatic Track Number Renewal Level Sensitivity SettingAuto Pause Mode Setting Sample Rate Converter ThruAutomatic writing of track number Track Number WritingManual writing of track number Press the Track no T O / M a N U a LCreating a blank Convenient Functions for RecordingTo pause recording Starting recording with fade-inChecking the recording end point from the middle of a disc Play the track to be skipped Setting skip ID to a track Track skipSkip ID Recording Press the Skip ID SET buttonClearing skip ID of a track Play the track which is not to be skippedRW disc which has Been recorded on What is finalization?Finalization TOC Recording Press the Finalize buttonErasing CD-RW only Erasing CD-RW discsLoad a CD-RW disc which has been finalized Load a CD-RW disc w h i c h h a s b e e n recorded onPress the Erase button Press the pause button to start the TOC erasingAll tracks erasing To pause playback PlaybackStarting playback Playing from the desired track Direct track selectionPress the track search Searching an adjacent track Track searchSearching the desired point Manual search Press and hold the manualPlaying tracks repeatedly Repeat playback Playback in Auto Pause ModePress the Repeat button of the remote control unit Fade-in/fade-out during playbackProgram reservation Programmed PlaybackPlaying Tracks in the Desired Order Programming pauseChecking the programmed tracks Clearing the entire programClearing a track from the program Replacing a track in the programCase skip playback is not required Load a disc containing the recording of skip ID dataPress the play button Character Message List Message Description Ref.Information messages related to recording operation Information messages related to playback operationSymptom Cause Remedy ConnectionsIndex Term Function Ref.Audio Unit typical Declaration of EC Directive Affect of Immunity on This EquipmentPage Fostex CO