Top Grille Panel – Routing Requirements
Top and bottom edges of the top panel should be edge routed ¹⁄₂" (1.3 cm) and ³⁄₈" (9.5 mm), respectively. Both ends should be
¹⁄₄" |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ¹⁄₄" |
(6.35 mm) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| (6.35 mm) |
|
|
|
|
|
|
|
|
|
| ||||||||
max. |
|
|
|
| Top | Top |
|
|
|
|
|
|
| max. | |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| Grille | Grille |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ⁷⁄₈" |
|
|
|
| ⁷⁄₈" |
|
|
|
|
| ||
|
|
|
|
|
|
| |||||||||||
|
|
|
|
| (2.2 cm) |
| (2.2 cm) | ||||||||||
NOTE: When creating a panel with face detail, the offsets will be hidden and must be accounted for in order to center the detail in the top grille.
|
|
|
|
|
| ¹⁄₄" |
|
|
|
|
|
| |
|
|
|
|
|
| (6.35 mm) max. |
¹⁄₂" |
|
|
| Top | ||
|
|
| ||||
(1.3 cm) |
|
|
|
|
|
|
min. |
|
|
|
|
|
|
Center face
Door Panel - Side View
¹⁄₄"
(6.35 mm) max.
¹⁄₂" (1.3 cm) min.
Panel
Overlay SeriesCustom Panels
Custom overlay panels allow you to blend the exterior of your refrigerator into the overall kitchen décor and to use custom handles for additional design flexibility.
The custom panels must have backer panels attached in order to mount them to the refrigerator. It is most common to work with three panels, as shown in the following graphic: a decorative overlay panel, a ¹/₈" (3.18 mm) spacer panel or spacer strips and a ¹/₄" (6.35 mm) backer panel.
detail between 
offsets
³⁄₈"
(9.5 mm) |
|
|
|
|
|
|
min. |
|
|
| Bottom | ||
|
|
|
| |||
|
|
|
|
|
| ¹⁄₄" |
|
|
|
|
|
| |
|
|
|
|
|
| (6.35 mm) max. |
|
|
|
|
|
| |
Door Panel – Routing Requirements
Overlay Panel | Spacer Panel | ||
|
| ||
|
| Backer Panel | |
5/8" to 3/4" |
| 1/4" | |
(15.88 to |
| ||
1/8" | (6.35 mm) | ||
19.05 mm) | |||
(3.18 mm) |
| ||
|
| ||
Spacer Panel |
1/8" |
(3.18mm) |
1" minimum |
(2.54 mm) |
Door/Grille Trim |
Offset Dimension |
If an extended handle kit is used, then routing the handle side of the door and drawer panels is not required. See “Classic, Architect®, and Overlay Series Factory Panels and Kits” for more information on ordering extended handles.
If the standard handle is used, rout the entire handle side 3¹⁄₄" (8.25 cm) to allow for finger clearance. Then rout the other side 1" (2.54 cm).
Standard Handle – Top View
In some cases, your cabinet manufacturer may choose to work with one panel routed for the different dimensions. Follow these panel dimension and placement instructions to be sure that the custom overlay panels will fit properly.
IMPORTANT:
■ The weight of the refrigerator door overlay panel cannot | |
| exceed 50 lbs (23 kg). |
■ | The weight of the freezer drawer overlay panel cannot exceed |
| 30 lbs (13.5 kg). |
■ | The weight of the top grille overlay panel cannot exceed |
Handle
3¹⁄₄"
(8.25 cm) min.
¹⁄₄" (6.35 mm) max.
2" (5 cm)
min.
Hinge Side
Door | Door |
Panel | Panel |
1"
(2.54 cm)
10 lbs (4.5 kg). |
To minimize panel weight, you may use 2" (5.08 cm) spacer strips around the perimeter in place of
(5.08 cm) strips horizontally centered for added support.
11