INSTALLATION
REQUIREMENTS
Toolsand Parts
IMPORTANT:
■Installer: Leave Installation Instructions with the homeowner.
■Homeowner: Keep Installation Instructions for future reference. Save these Installation Instructions for the local electrical inspector’s use.
TOOLS NEEDED:
Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.
■ Hand drill or electric drill | ■ | Torx®† T27 screwdriver | |
| (properly grounded) |
|
|
■ | Drill bits | ■ | ¹¹⁄₃₂" nut driver |
■ | Two adjustable wrenches | ■ | ³⁄₈" and ¹⁄₂" |
|
|
| wrenches |
■ | Phillips screwdriver | ■ | ⁵⁄₃₂" Allen wrench |
■ | Small level | ■ | ⁵⁄₁₆" socket wrench |
■ | Appliance dolly | ■ | Tape measure |
PARTS NEEDED:
■Six #8 x 3" (7.6 cm) wood screws (longer screws may be needed)
■One or two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) wood board(s)
■Order factory panels, make custom panels or consult a qualified cabinetmaker or carpenter to make the panels.
Classic Series: Order factory panels, make custom panels, or consult a qualified cabinetmaker or carpenter to make the panels. See “Design Specifications” for more information.
Overlay Series: Make custom panels, or consult a qualified cabinetmaker or carpenter to make the panels. See “Design Specifications” for more information.
Complete, Architect® and Pro Line® Series are shipped complete.
■If you are connecting the water line directly to copper tubing and not to a shutoff valve, you need a ferrule, a union, and a ¹⁄₄" (6.35 mm) compression fitting.
Location Requirements
The refrigerator can be recessed in an opening between cabinets or installed at the end of a cabinet run using a side panel to enclose the refrigerator.
WARNING
Explosion Hazard
Keep flammable materials and vapors, such as gasoline, away from refrigerator.
Failure to do so can result in death, explosion, or fire.
IMPORTANT:
■Observe all governing codes and ordinances.
■It is recommended that you do not install the refrigerator near an oven, radiator, or other heat source.
■Do not install in a location where the temperature will fall below 55°F (13°C).
■Floor must support the refrigerator weight, more than 600 lbs (272 kg), door panels and contents of the refrigerator.
■Ceiling height must allow for side tipping radius. See “Tipping Radius.”
■Location should permit door to open fully. See “Door Swing Dimensions.”
■Location must permit top grille removal. See “Opening Dimensions.”
Opening Dimensions
■The solid soffit must be within 1" (2.5 cm) maximum above the refrigerator. If the solid soffit is higher than 1" (2.5 cm) or one is not available, then the refrigerator must be braced to prevent tipping during use.
If the
NOTE: A clearance of ¹⁄₂" (1.3 cm) must be maintained in front of the refrigerator’s side trim in order for the top grille to be removed.
¹⁄₂"
(1.3 cm)
■ A grounded 3 prong electrical outlet should be placed within 4" (10.2 cm) of the right side cabinets or end panel. See “Electrical Requirements” for additional information.
■ The water shutoff should be located in the base cabinet on either side of the refrigerator or some other easily accessible area. If the water shutoff valve is not in the cabinets, the plumbing for the water line can come through the floor or the
†®TORX is a registered trademark of Textron Innovations Inc.
14