KitchenAid 2307890A manual Install Base Grille, Water System Preparation, Complete Installation

Page 23

IMPORTANT: KitchenAid is not responsible for the removal or addition of molding or decorative panels that would prevent the refrigerator from being serviced.

1.For the inside side trim piece, slide the front edge of the routed side panel into the trim piece.

2.Nail the rear edge of the panel to the support board.

A

B

A. Support board

B. Side trim piece

Install Base Grille

There are two pieces to the base grille to allow for a custom fit: the base grille itself and the skirt. The skirt can be added to the base grille in order to extend it all the way to the floor.

1.Open the refrigerator door and measure the distance from the bottom of the refrigerator cabinet to the floor.

B

 

 

 

 

 

 

 

 

 

 

 

 

A

 

 

 

 

C

 

 

 

 

 

 

 

 

 

 

A.Floor

B.Refrigerator cabinet bottom

C.Distance to be measured

2.Measure this same distance from the top of the base grille to the closest “V” groove on the skirt. Use a knife to score down the “V” groove and break the skirt at the score line.

A

B

C

A. Grille and skirt assembly

B. Measured distance from above in Step 2

C. Score “V” groove

3.Slide the skirt onto the base grille.

4.Then attach the base grille to the cabinet with the two screws provided.

Water System Preparation

Please read before using the water system.

Immediately after installation, follow the steps below to make sure that the water system is properly cleaned.

1.Turn off the ice maker by opening the freezer door and lifting up the wire shutoff arm as shown.

NOTES:

If your model has a base grille filter system, make sure the base grille filter is properly installed and the cap is in the horizontal position.

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.

2.Turn on the ice maker by opening the freezer door and lowering the wire shutoff arm as shown. Please refer to the “Ice Maker and Storage Bin” section in the Use & Care Guide for further instructions on the operation of your ice maker.

Allow 24 hours to produce the first batch of ice.

Discard the first three batches of ice produced.

Complete Installation

1.Turn the water supply line valve to the “Open” position.

2.Turn the refrigerator switch to the ON position. See “Power On/Off Switch” in the Use & Care Guide for instructions. Wait a few minutes. Check the water line connections for leaks.

3.Remove all boxes, parts packages and packing materials from the interior of the refrigerator. See the “Cleaning” section in the Use & Care Guide for instructions. Remove the protective film and cardboard from the grille and doors or door frame, depending on your model.

4.Install the shelves and bins in the refrigerator and freezer compartments.

5.The controls are preset at the factory to the midpoint setting. Check to be sure that the compressor is operating properly and that all the lights are working.

6.If construction will continue after the refrigerator has been installed, set the controls to OFF.

To get the most efficient use from your new built-in refrigerator, read your Use & Care Guide. Keep Installation Instructions and Use & Care Guide near the built-in refrigerator for easy reference.

23

Image 23
Contents BOTTOM-MOUNT BUILT-IN Refrigerator Table of Contents/Índice/Table des matièresTable DES Matières Table of ContentsÍndice Your safety and the safety of others are very important Refrigerator SafetyModels Design SpecificationsPro LineTM Series Product DimensionsSide View Top ViewSide Tipping Radius Door Swing DimensionsTipping Radius Front ViewHandle and Door Clearances Overlay Series Door Top Grille Panel Classic SeriesCustom PanelsFactory Door Panel Kits Extended Door Handle KitsDoor Panel Side View Overlay SeriesCustom PanelsTop Grille Panel Routing Requirements Door Panel Routing RequirementsArchitect SeriesCustom Side Panels Measure the distance from point a as shown to back wall Recessed Inset Installation DimensionsLocation Requirements Installation RequirementsOpening Dimensions Toolsand PartsMm of the rear wall Electrical RequirementsWater Supply Requirements Recommended Grounding MethodReduce TippingRadius Installation InstructionsUnpack the Refrigerator Pro Line Series Install Anti-Tip BoardsTo Install Anti-tip Boards Move the Refrigerator into HouseStyle 2 Shutoff Valve Connection Connecting to Refrigerator Style 1 Copper Line ConnectionConnectthe Water Supply Connect to Water LineLower LevelingLegs Install ClassicSeries Custom PanelsPlug in Refrigerator MoveRefrigerator toFinal LocationDoor Panel Installation Install OverlaySeries Custom PanelsLevel Refrigerator Install Side Panel Adjustand Remove DoorWater System Preparation Install Base GrilleComplete Installation Su seguridad y la seguridad de los demás es muy importante Seguridad DEL RefrigeradorModelos Especificaciones DE DiseñoSerie Pro LineTM Medidasdel productoVista lateral Vista superiorArco de vuelco lateral Medidas de oscilación de la puertaArco devuelco Vista frontalEspaciospara la agarradera y la puerta Serie Overlay Soporte Panel de la rejilla superior Panelesde la puerta a la medida para la Serie ClassicJuegos de paneles para puertas de fábrica Juegos de extensión de agarraderas de puertaAgarradera común Vista superior Paneles a la medida de la Serie OverlayRequisitos de contorneado del panel de la rejilla superior Requisitos de contorneado de los paneles de la puertaAdornos laterales Paneles laterales a la medida para la Serie ArchitectMedidas del refrigerador y del adorno lateral RefrigeradorMedidas para la instalación en relieve Medidas para la instalación empotradaMedidas para la instalación al ras Medidas de la abertura Requisitos DE InstalaciónPiezas y Herramientas Requisitosde ubicaciónMétodo de conexión a tierra recomendado RequisitoseléctricosPresión del agua Instrucciones DE InstalaciónRequisitosdel suministro de agua Cómo desempacar surefrigeradorSerie Pro Line Cómoreducirelarco devuelcoCómohacer entrar el refrigerador en la casa Series Classic y OverlayConexión a la línea de agua Cómo instalar los tablerosantivuelcoConexión del suministro de agua Cómo instalar los tableros antivuelcoAbra la válvula de cierre Cómo enchufar el refrigeradorEstilo 2 Conexión de la válvula de cierre Paneles de la puerta y cajón Ubicación final delrefrigeradorBaje las patas niveladoras Cómo instalar los paneles a la medida para la Serie ClassicInstalación del panel de la puerta Cómo instalar los paneles a la medida para la Serie OverlayCómonivelar el refrigerador Cómo ajustar la oscilación de las puertas Cómo ajustary quitarlaspuertasCómo quitar y alinear la puerta Siga los siguientes pasos para volver a instalar la puertaCómo instalar la rejilla de la base Cómoinstalar el panellateralCómoterminarla instalación Preparación del sistema de aguaVotre sécurité et celle des autres est très importante Sécurité DU RéfrigérateurModèles Spécifications DE DesignSérie Pro LineTM Dimensionsdu produitVue latérale Vue de dessusRayon de basculement latéral Dimensions pour le pivotementdes portesRayon debasculement Vue avantDégagementspourlespoignées et portes Série Overlay Panneau Panneau de la grille supérieure Panneaux personnalisés de la Série ClassicEnsembles de panneaux de porte dorigine Ensembles de poignées de porte prolongéesPoignée standard Vue supérieure Panneaux personnalisés de la série OverlayExigences dusinage du panneau de la grille supérieure Exigences dusinage des panneaux de porteRéfrigérateur Dimensions du réfrigérateur et des garnitures latéralesDimensions pour un panneau inséré Panneaux latéraux personnalisésde la Série ArchitectDimensions pour un panneau inséré en retrait Réfrigérateur Dimensions pour un panneau en affleurementOutillage etpiècesnécessaires Exigences ’INSTALLATIONExigences d’emplacement Dimensions de l’ouvertureUne source dalimentation de 115 volts, 60 Hz, type 15 ou Méthode recommandée de mise à la terreSpécificationsélectriques Pression de leau Instructions ’INSTALLATIONSpécifications de l’alimentation en eau Déballage du réfrigérateurSérie Architect Réduction du rayon de basculementFaire entrerle réfrigérateur dans le domicile Séries Classic et OverlayRaccordement à une canalisation d’eau Installation de planchesantibasculementInstallation des planches antibasculement Raccordement delacanalisation deauStyle 2 Raccordement au robinet darrêt Déplacementdu réfrigérateur à Lemplacement finalBrancher le réfrigérateur Déploiement despiedsde nivellementPanneaux de porte et de tiroir Installation des panneaux personnalisés de la Série ClassicInstallation des panneaux de porte Installation des panneaux personnalisés de la Série OverlayEnlèvement et alignement des portes Suivre les étapes suivantes pour réinstaller la porteNivellementdu réfrigérateur Ajustementetenlèvement desportesTenir la porte ouverte à une position de moins de Installation du panneau latéralAjustement de l’ouverture des portes Veuillez lire avant d’utiliser le système d’eau Installation de la grille de la baseAcheverl’installation Préparation du système d’eau