NOTE: For the grille and the door panels to be flush, the overlay door panel should be ¹⁄₄" (6.35 mm) thicker than the overlay grille panel.
■The side panel should be a minimum of ¹⁄₂" (12 mm) thick to prevent warping.
■If the opening depth is 25" (63.5 cm) or more, you may want to install a support board on the rear wall.
81/2"
(21.59 cm)
341/2"
(87.63 cm)
73/8"
(18.73 cm)
341/2" (87.63 cm)
Bottom Offset
1" (2.54 cm)
341/2"
(87.63 cm)
Refrigerator
24¹⁄₈"
(61.3 cm)
23¹¹⁄₁₆"
(60.3 cm)
23¹⁄₂"
(59.7 cm)
50"
(127.0 cm)
345/16"
(87.15 cm)
491/8"
(124.78 cm)
Bottom Offset 7/16" (11.1 mm)
Center
Backer
Panel left to right
Side Trim
¹⁄₄" 
(6.35 mm)
¹¹⁄₆₄"
(4.5 mm)
³⁄₁₆" 
(4.7 mm)
⁷⁄₃₂"
(5.5 mm)
209/16"
(52.23 cm)
|
|
| 341/2" |
|
|
|
|
| ||
|
|
|
| (87.63 cm) |
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| 345/16" |
|
|
| Center | |||
|
|
|
|
|
|
| ||||
|
|
|
|
| (87.15 cm) |
|
|
| ||
|
|
|
|
|
|
|
| Backer | ||
|
|
|
|
|
|
|
|
|
| |
203/16" |
|
|
|
|
| Panel | ||||
(51.28 cm) |
|
|
| left to | ||||||
|
|
|
|
|
|
|
|
|
| right |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Bottom Offset | |||
|
|
|
|
|
|
| 1/16" (1.6 mm) | |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
¹³⁄₃₂" (10 mm) |
|
| ⁵⁄₈" |
|
| |||||
|
| |||||||||
|
| (15.7 mm) | ||||||||
|
|
|
|
|
|
| ||||
Inset Installation Dimensions
1.Measure the distance from point A (as shown) to the back wall. Add ⁷⁄₃₂" (5.6 mm) to this measurement to allow the side panel to fit into the trim.
2.If the panel is more than ¹⁄₄" (6.35 mm) thick, rout the front edge to allow the side panel to fit into the trim.
Architect® SeriesCustom Side Panels
Custom side panels may be needed when not enough space is
available to have cabinets on both sides of the refrigerator orA when the refrigerator is placed and the end of a cabinet run. You
may choose an Inset, Flush, or Recessed Inset panel installation.
Refrigerator and Side Trim Dimensions
The width and height of a side panel are determined by the type of installation you are planning.
NOTES:
■The dimensions shown are actual product dimensions and may not reflect the needed panel installation dimensions.
Flush Installation Dimensions
1.Measure the distance from point A (as shown) to the back wall.
2.Attach the support board with a screw or adhesive that is compatible with aluminum and wood.
A
12