Connectthe Water Supply
Read all directions before you begin.
IMPORTANT: If you turn the refrigerator on before the water line is connected, turn the ice maker OFF.
Connect to Water Line
1.Unplug refrigerator or disconnect power.
2.Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.
3.Locate a ½" to 1¹⁄₄" (1.25 cm to 3.18 cm) vertical cold water pipe near the refrigerator.
IMPORTANT:
■Make sure it is a cold water pipe.
■Horizontal pipe will work, but drill on the top side of the pipe, not the bottom. This will help keep water away from the drill and normal sediment from collecting in the valve.
4.Determine the length of copper tubing you need. Measure from the connection on the lower left rear of refrigerator to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use ¹⁄₄" (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.
5.Using a grounded drill, drill a ¹⁄₄" hole in the cold water pipe you have selected.
NOTE: Tighten the nut by hand. Then tighten it with a wrench two more turns. Do not overtighten.
A | B | C | D | E F G |
A. Refrigerator water tubing |
| E. Ferrule (purchased) | ||
B. Nut (provided) |
|
| F. Nut (purchased) | |
C. Bulb |
|
|
| G. Household water |
D. Coupling (provided) |
| line | ||
3.Turn shutoff valve ON.
4.Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak.
NOTE: Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced. Allow 3 days to completely fill ice container.
Style 2 - Shutoff Valve Connection
1.Remove the shipping tape from the gray, coiled water tubing on the rear of the refrigerator.
2.Thread the provided nut onto the water valve as shown.
NOTE: Tighten the nut by hand. Then tighten it with a wrench two more turns. Do not overtighten.
G
F E
A. Cold water pipe B. Pipe clamp
C. Copper tubing D. Compression nut
A
B
C
D
E. Compression sleeve
F.Shutoff valve G. Packing nut
A |
B |
6.Fasten the shutoff valve to the cold water pipe with the pipe clamp. Be sure the outlet end is solidly in the ¹⁄₄" drilled hole in the water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp screws slowly and evenly so washer makes a watertight seal. Do not overtighten, or you may crush the copper tubing.
7.Slip the compression sleeve and compression nut on the copper tubing as shown. Insert the end of the tubing into the outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten the clamp or the sleeve. This will crush the copper tubing.
8.Before attaching copper tubing to the refrigerator place the free end of the tubing in a container or sink and turn on the main water supply. Flush at least 2 qt (1.9 L) of water through the copper tubing until water is clear to get rid of any particles in the water line. Turn off the shutoff valve on the water pipe. Coil the copper tubing.
9.Check for leaks around the saddle valve.
Connecting to Refrigerator
Style 1 - Copper Line Connection
1.Remove the shipping tape from the gray, coiled water tubing on the rear of the refrigerator.
2.A ¹⁄₄" x ¹⁄₄" coupling is needed in order to connect the water tubing to an existing household water line. Thread the provided nut onto the coupling on the end of the copper tubing.
A.Bulb
B.Nut (provided)
3.Turn shutoff valve ON.
4.Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak.
NOTE: Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced. Allow 3 days to completely fill ice container.
18