KitchenAid LI3ZBC/W10331009C Make Electrical Connections for In-Line Blower Motor System

Page 11

A

B C

D

A. Front cover

C. Spring clip

B. Blower mounting screws

D. Motor electrical plug

Install In-line Blower System

NOTE: The blower motor housing can be mounted using 4 holes from either the outlet side or the inlet side of the blower.

Outlet Side:

AA

A

A

A. Mounting holes

Inlet Side:

A

A

A. Mounting holes

1.Position the in-line blower motor housing in its mounting location and mark the 4 mounting hole locations.

2.Drill 4 mounting pilot holes using a ³⁄₁₆" (0.48 cm) drill bit.

3.Attach the in-line blower motor housing to the mounting location with four 6 x 80 mm mounting screws and washers.

4.If it is removed, reinstall the blower motor assembly and secure it with the screws previously removed.

5.If it is removed, reattach the motor electrical plug to the connector on the blower motor assembly.

Complete Preparation

1.Determine and make all necessary cuts for the vent system.

IMPORTANT: When cutting or drilling into the ceiling or wall, do not damage electrical wiring or other hidden utilities.

2.Determine the location where the ¹⁄₂" (1.3 cm) wiring conduit will be routed through the ceiling or wall between the in-line blower and the range hood.

3.Drill a 1¹⁄₄" (3.2 cm) hole at this location.

4.Locate the electrical terminal boxes in the in-line blower housing and range hood. Remove the terminal box covers and set the covers and screws aside.

B

A

A. Electrical terminal box

B. Electrical knockout

5.Remove the electrical knockout from the in-line blower housing and range hood to prepare for the installation of the UL listed or CSA approved ¹⁄₂" (1.3 cm) wiring conduit and conduit connector.

6.With the range hood mounted (see the “Install Range Hood” section), run the ¹⁄₂" (1.3 cm) wiring conduit between the in- line blower motor housing and the range hood. Pull enough ¹⁄₂" (1.3 cm) wiring conduit to allow for easy connection to the terminal boxes in the in-line blower housing and range hood.

7.Run the six 18 AWG wires through the ¹⁄₂" (1.3 cm) wiring conduit and conduit connectors and into the terminal boxes on the in-line blower housing and range hood. Leave enough wire length in each terminal box to make the wiring connections.

8.Install the conduit connectors and conduit to the in-line blower housing and range hood electrical terminal boxes.

9.Connect the vent system to the range hood and in-line blower system and seal all joints with clamps.

Make Electrical Connections for In-Line

Blower Motor System

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

Electrical Connection Inside In-line Blower System

1.Disconnect power.

2.Connect the wires from the wiring conduit to the wires from the motor electrical plug cable inside the in-line blower housing terminal box.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents COMMERCIAL-STYLE WALL-MOUNT Canopy Range Hood Table DES Matières Table of ContentsRange Hood Safety Important Safety Instructions Location Requirements Installation RequirementsTools and Parts For the Most Efficient and Quiet Operation Installation DimensionsCold Weather Installations Venting RequirementsExample Vent System Typical In-line Blower Motor System Venting InstallationsElectrical Requirements Calculating Vent System LengthPrepare Location Installation InstructionsRange Hood Mounting Screws Installation Chimney Support Bracket InstallationPrepare the Internal Blower System Install Range HoodInstall Range Hood Internal Blower Motor Dual Blower Motor Assembly Install Range Hood Internal Blower MotorSingle Blower Motor Assembly Prepare the In-line Blower System Install Range Hood In-Line External Type Blower MotorPrepare for Mounting the In-Line Blower System Electrical Connection Inside In-line Blower System Install In-line Blower System Outlet SideMake Electrical Connections for In-Line Blower Motor System Inlet SideTogether Complete Preparation in the Prepare Location sectionRange Hood Install Chimney CoversInstall Upper Chimney Cover Install Lower Chimney CoverRange Hood Controls Complete Installation and Check OperationRange Hood USE Range Hood Care CleaningMotor Resistance Ohms Canada Assistance or ServiceAccessories U.S.AThis limited warranty does not cover Kitchenaid Ventilation WarrantyVotre sécurité et celle des autres est très importante Sécurité DE LA Hotte DE CuisinièreImportantes Instructions DE Sécurité Outils et pièces Exigences DinstallationExigences d’emplacement Air dappoint Dimensions à respecter lors de l’installationInstallations pour régions à climat froid Exigences concernant lévacuationDécharge à travers le toit Décharge à travers le mur Spécifications électriquesExemple de système de décharge Calcul de la longueur effective du circuit dévacuationInstallation de la bride de support de la cheminée Instructions D’INSTALLATIONPréparation de l’emplacement Installation des vis de montage de la hottePréparer le système de ventilation interne Installation de la hotteInstallation du moteur du ventilateur interne De la hotte Achever la préparationEnsemble à deux moteurs-ventilateurs Installation du moteur du ventilateur interne de la hotteEnsemble à un seul moteur-ventilateur Avertissement Côté entrée Installation du système de ventilation en ligneCôté sortie Une fois la hotte montée voir la section Instructions Homologation UL Installation du cache-cheminéeUtilisation DE LA Hotte Achever linstallation et vérifier le FonctionnementInstallation de la section supérieure du cache-cheminée Installation de la section inférieure du cache-cheminéeCommandes de la hotte de cuisinière Nettoyage Entretien DE LA HotteRésistance du moteur ohms Au Canada Assistance OU ServiceAccessoires W10331009C Garantie DU Système DE Ventilation KitchenaidLa présente garantie limitée ne couvre pas
Top Page Image Contents