Cornelius 000 PLUS Not Form Sufficient ICE, Wiring Diagram, Condenser FAN Motor, Not Operating

Page 39

Trouble

 

Probable Cause

 

Remedy

COMPRESSOR OPERATES

E.

Inoperative control board. No

E.

Check LED’s on control board to

CONTINUOUSLY BUT DOES

 

output from board to

 

see if they are modulating. Check

NOT FORM SUFFICIENT ICE

 

solenoids.

 

for 24V output to pulse

BANK (con’t).

 

 

 

modulating expansion valve (see

 

 

 

 

WIRING DIAGRAM).

 

 

 

 

If control board green LED is on

 

 

 

 

and yellow LED Is flashing; but no

 

 

 

 

24V output, replace board.

CONDENSER FAN MOTOR

A.

Blown power circuit fuse.

A.

Replace power circuit fuse.

NOT OPERATING

 

 

 

 

 

B.

Fan blade obstructed.

B.

Remove obstruction.

 

C.

Inoperative condenser fan

C.

Replace condenser fan motor.

 

 

motor.

 

 

 

D.

Compressor contactor

D.

Replace compressor contactor.

 

 

inoperable.

 

 

AGITATOR MOTOR NOT

A.

Agitator motor propeller

A.

Remove obstruction.

OPERATING.

 

obstructed.

 

 

 

B.

Low voltage.

B.

Voltage must be at least 208 volts

 

 

 

 

at compressor terminals when

 

 

 

 

compressor is trying to start.

 

C.

Loose, disconnected, or

C. Tighten connections or replace

 

 

broken wiring.

 

broken wiring.

 

D.

Inoperative agitator motor.

D.

Replace agitator motor.

 

 

 

 

 

35

300614000

Page 38 Page 40
Image 39
Page 38 Page 40
Contents This Document Contains Important Information AURORAR10,000 Plus Cooling UnitTable of Contents Table of Contents cont’d Water Pump Motor Operates but Water Pump does not Pump Cooling Unit CO2 Inlet Line CO2 GAS Check ValveWATER-TO-SYRUP ‘RATIO’OF Dispensed Drink TOO LOW or TOO Dispensed Product Produces Foam AS IT Leaves DispensingCooling Unit Description General DescriptionCooling Unit Data System Theory of Operation Flow Diagram Typical Installation Cooling Unit Unpacking and InspectionIdentification of LOOSE-SHIPPED Parts Selecting LocationPlacing Cooling Unit in Location Installing Remote Condenser Coil and FAN ASS’YInstalling Cooling Unit Remote Condenser Coil and FAN ASS’YConnecting Electrical Power Circuit to Cooling Unit Cooling Unit factory warranty Connecting Plain Water Inlet Supply Line to Cooling UnitConnecting CO2 Inlet Supply Line to Cooling Unit Preparing Cooling Unit for Operation Placing Cooling Unit in Operating PositionOperation Service internal components or electrical wiringAdjusting WATER-TO-SYRUP ‘‘RATIO’’ of Dispensed Product Dispensing Station AdjustmentsInstalling Line Identification Label Adjusting Water Flow RateOperating Controls Cooling Unit Refrigeration Power SwitchCooling Unit Carbonator Motor Switch Cooling Unit Circulating Motor SwitchReplenishing CO2 Supply AdjustmentsCleaning and Sanitizing Daily PRE-OPERATION CheckCooling Unit AIR Intake and Exhaust Filters Cooling Unit MaintenanceCooling Unit Carbonator Maintenance Sanitizing Syrup SystemsCleaning CO2 GAS Check Valves Remote Condenser Coil and FAN ASS’Y MaintenancePeriodic Inspection Periodic CleaningCleaning Cooling Unit AIR Intake and Exhaust Filters Preparing Cooling Unit for SHIPPING, STORING, or RelocatingChanging ICE Water Bath Remote Condenser Coil and FAN Assembly MaintenanceSee Figures 2 Parts Identification Lubrication Primary CO2 RegulatorSecondary CO2 Regulators Daily Cleaning of Unit Water Flow RateWATER-TO-SYRUP ‘‘RATIO’’OF Dispensed Product Wash Syrup Systems Sanitizing POST-MIX Syrup SystemsFlush Syrup Systems Sanitize Syrup SystemsWater Flush Syrup Systems Purge Water OUT of Syrup Systems Restore Operation CO2 GAS Check Valve Replenishing Syrup SupplyCleaning CO2 System GAS Check Valves Syrup Flavor ChangeCooling Unit CO2 Inlet Line CO2 GAS Check Valve 300614000 Wiring Diagram LOW or TOO High AdjustmentWATER-TO-SYRUP ‘RATIO’ Dispensed Drink TOOOnly Carbonated Water a Dispensed ProductCarbonation TOO LOW Comes OUT Dispensing Valve Clear But Foams in CUPWarm Product Being Only Carbonated WaterOnly Syrup Dispensed Carbonator MotorOperates but Water Operate Refrigeration PowerTemperature Sensing Water Pump MotorCompressor Operates Continuously but doesNot Form Sufficient ICE Bank Not Operating Wiring DiagramNot Form Sufficient ICE Condenser FAN MotorWarranty This page Left Blank Intentionally One Cornelius Place Anoka, Minnesota 612 800
Related manuals
Manual 52 pages 8.37 Kb

000 PLUS, 10 specifications

Cornelius 10,000 PLUS is a pioneering innovation in the beverage dispensing industry, designed to cater to the evolving needs of commercial establishments. This advanced system combines state-of-the-art technology with user-friendly features, making it a standout choice for restaurants, cafes, and bars aiming to enhance their beverage service.

One of the main features of the Cornelius 10,000 PLUS is its impressive capacity. With the ability to dispense a wide variety of beverages, including soft drinks, cocktails, and craft beers, the system supports a large volume of service, perfect for high-demand environments. The modular design allows for easy expansion, enabling businesses to add additional flavors or beverages as needed without major overhauls.

The technology behind the Cornelius 10,000 PLUS is equally impressive. It utilizes advanced cooling technology to ensure that beverages are served at the optimal temperature, enhancing the customer experience. The integrated touchless dispensing mechanism minimizes waste and ensures a hygienic experience, addressing growing concerns about cleanliness in food service environments. This technology also improves speed, allowing staff to serve customers more efficiently.

Another key characteristic of the Cornelius 10,000 PLUS is its digital integration capabilities. The system can be connected to a central management platform that tracks sales, inventory levels, and maintenance needs in real-time. This allows operators to optimize their beverage offerings based on customer preferences and reduces downtime through proactive maintenance alerts.

In addition to its performance features, the Cornelius 10,000 PLUS is designed with sustainability in mind. The system employs energy-efficient practices, reducing its environmental footprint while lowering operational costs. The materials used in construction are durable yet eco-friendly, ensuring longevity and less waste.

Overall, the Cornelius 10,000 PLUS stands out as an essential tool for any business looking to elevate its beverage service. With its combination of high capacity, cutting-edge technology, and sustainability features, it not only meets the demands of today’s fast-paced service environments but also positions establishments for future growth and success.
Top Page Image Contents