Whirlpool 4322452 manual Burner Flame Adjustment

Page 68

BURNER FLAME ADJUSTMENT

After converting the range to L.P. gas operation, it may be necessary to adjust each burner flame (cooktop and oven burners). A proper cooktop burner flame should be approximately 5/8" high and have a well-defined blue flame. The oven burner flame should be approximately 3/4" high and have a distinct blue flame. If the flame is noisy, or blowing off the burner, it is getting too much air. If the flame is soft and lazy, it is not getting enough air. Air adjustments can be made by adjusting the air shutter at each burner (see Figures 5-5A, B, & C). NOTE: There is no air adjustment for sealed burner cooktops.

Air Shutter

Cooktop

Burner

Bake Burner Air Shutter

Figure 5-5A

Figure 5-5B

Broil Burner Air Shutter

Figure 5-5C

Page 5-4

Image 68
Contents GAS Ranges Voltage Checks Table Of Contents Page Introduction Page Fundamental Properties of GAS Measuring Heat EnergyFuel Types #2 Mixed GAS#3 Manufactured GAS #4 Liquefied Petroleum L.P. GASCategory Characteristics of GAS Fuels FuelDistribution of Natural GAS 25 To 60 Pounds Pressure MainDistribution of L.P. GAS Pressure Regulators FunctionsRegulator Operation Open Position Regulator Diagnostics VentingMeasuring GAS Pressure WHIRLPOOL, U.S.A., Benton HARBOR, MIMagnehelic Gauge Cooktop Burner System GAS DistributionGAS Valve OFF PositionGAS Valve Orifices PLUG-TYPE OrificesOrifice Specifications Chart Natural GAS OrificesUniversal ORIFICE-OVEN Application Natural Gas PositionGAS Valve Orifice Diagnostics Performance Check Burner Operation AIR Shutter & Venturi Burner Head Flame Characteristics Properly Burning FlameNot Enough Primary Air Flame Quenching Page Improper Flame Diagnostics Symptom Cause Corrective ActionCleaning the Burners Port Burner Climber PortStanding Pilot Ignition System OperationRelighting a Standing Pilot Adjusting the Pilot Flame Height Cleaning the Pilot Electronic Ignition System 123Ground Strap Ignitor Spark Sealed Burner FlowElectronic Ignition Diagnostics Performance Check Oven Burner System Standing Pilot IgnitionGas Standing Pilot Safety Valve Lighting the Oven Pilot GLO-BAR Ignition Thermostat Switch Contacts Oven Ignitor Safety Valve 50 to 1100 Ω Amps Safety Valve Thermostat Switch Contacts Oven Ignitor Safety Valve Cleaning the Oven Burner SELF-CLEANING System 88PBK P3-1 P3-4 Oven Off Bake Cycle Broil Cycle Bake BroilCode Guidelines F0 =Performance Check SELF-CLEAN Oven Door Locking System Door Locked Door Unlocked Natural and L.P. GAS Conversion GeneralConverting a Pressure Regulator Converting Cooktop BurnersConverting AN Oven Burner Converting AN Oven ThermostatBurner Flame Adjustment Performance Check Page Testing the Components General Information Testing AN Oven GLO-BAR Igniter Carborundum IgnitorTesting AN Ignitor Switch Offoff LiteliteTesting AN Oven Light Switch Testing AN Oven Temperature Sensor Testing AN Oven Door Latch To test the solenoid windings, perform the following stepsTo test the switches Testing a GAS Safety Valve Testing the GAS Control Valves Testing the GAS Pressure Regulator Manual Shutoff ValveTroubleshooting Chart Problem Possible Cause SolutionProblem Possible Cause Solution Schematic Diagrams Standard RangeSelf-Clean Range Strip Circuits BakeOven Light