Southbend STRE-3D owner manual Electrical Connection

Page 17

STRATOSTEAM COUNTERTOP STEAMER

INSTALLATION

STEP 5: ELECTRICAL CONNECTION

The electric connection is made to the contactor, which is located inside the service compartment on the right side of the steamer. The right side panel must be removed to gain access to the contactor. A hole on the rear of each steamer is provided for a 3/4" conduit fitting (solid or flex). An electric cable support bracket and clamp are located inside of the service compartment, to the right and above the contactor (see Figure 8).

Be sure that the input voltage and number of phases matches the requirement stated on the serial plate. The steamer is factory wired per customer order. A wiring diagram is attached to the inside of the right side panel of the steamer.

WARNING

A POSITIVE GROUND CONNECTION IS ESSENTIAL. DO NOT ALLOW ANY TAMPERING OR ADJUSTMENT OF ANY CONTROL OR WIRING. THE STEAMER IS FACTORY SET. ADJUSTING ANY INTERNAL COMPONENT CAN VOID THE WARRANTY.

THIS STEAMER REQUIRES A KIT TO BE FIELD CONVERTED FROM THREE-PHASE TO SINGLE-PHASE OR VICE-VERSA. CONSULT FACTORY FOR PHASE CHANGES.

For 3-wire 3-phase installations, connect wires L1, L2, and L3 to the three terminals on the upper end of the contactor. For 2-wire 1-phase installations, connect wires L1 and L2 to the two outer terminals on the upper end of the contactor.

Make the electrical ground connection to the ground lug located at the top right-hand corner of the contactor bracket.

Figure 9

 

 

 

 

Electrical Connection

 

 

 

 

 

Contactor

Cable Support

 

 

 

Bracket

 

 

 

 

(with clamp)

 

 

 

 

Hole for

 

 

 

 

Cable Conduit

 

 

 

 

(with fitting)

 

Connections

Connections

to Contactor for

to Contactor for

3-Phase Models

1-Phase Models

L1

L2

L3

L1

L2

 

 

Top of

Top of

 

 

 

Steamer

Steamer

 

 

 

OWNER’S MANUAL 1185184

 

PAGE 17 OF 48

Page 16 Page 18
Image 17
Page 16 Page 18
Contents StratoSteam Safety Precautions Location of Serial Plates IntroductionClearances SpecificationsDimensions Right Side View DimensionsDrain Requirements Electrical RequirementsWater Requirements Operation Troubleshooting by OperatorStartup OperationCooking Tips ControlsSuggested Cooking Times Daily Cleaning and Maintenance Cleaning & MaintenancePeriodic DE-LIMING AS Needed STAINLESS-STEEL SurfacesStratosteam Countertop Steamer Cleaning & Maintenance Unpacking InstallationAttach Legs Attach LegsAttach to Countertop Installation on CountertopMounting on Cabinet Base Stacking TWO SteamersDrain Connection Location of Connections and VentsWater Connection Water DrainWater Connection Electrical Connection Electrical ConnectionCheck Steamer Operation Check the InstallationSHUT-DOWN and WIPE-CLEAN Steamer Troubleshooting FLOWCHARTS, PROCEDURES, and Wiring Diagrams ServiceHOW the Steamer Operates How the Steamer Operates Disconnect Power AT Circuit Breaker Steamer Not Heating Up, Power Light Is Not LitCheck that water-supply pressure is adequate Buzzer Does Not Come On When Timer Runs Out Heating Cartridge Check at Contactor Disconnect Power AT Circuit BreakerPower Switch Check Contactor Check Timer and Buzzer Check Door Switch Check High-Limit Thermostats Check Water-Level-Control Sensor Check Water Solenoid Check Wiring Diagram for 208/220/240 Volt Models Wiring Diagram for 480 Volt Models Parts Parts DiagramStructural Parts See parts list on previous Door Assembly Parts Door Switch Parts Control Panel Parts Heating Cartridges, Thermostats, and Contactor Parts Water Train Parts Water-Train Parts Cabinet Base Parts Cabinet-Base Parts Stratosteam Countertop Steamer Stratosteam Countertop Steamer StratoSteam Countertop Steamer Models STRE-3D and STRE-5D
Top Page Image Contents