Southbend STRE-3D Installation on Countertop, Attach to Countertop, Mounting on Cabinet Base

Page 14

INSTALLATION

STRATOSTEAM COUNTERTOP STEAMER

STEP 2B: ATTACH TO COUNTERTOP

If the steamer is to be installed on a countertop or other surface without using legs, the steamer must be sealed to the surface to prevent any water, grease, etc., from accumulating under the steamer. The steamer can be bolted to the surface, but will still have to be sealed. Make sure that the installed steamer is level before applying the sealant.. The installer may use GE® or Dow Corning® RTV type sealant. Consult local code for exact requirements.

1.Lower the steamer gently onto a level surface. Never drop or allow the steamer to fall.

2.If desired, bolt the steamer to the surface (use 3/8-16 bolts to fit the threaded holes used by the legs).

3.Make sure that the steamer is level (both side-to-side and front-to-back).

4.Apply sealant around all four bottom edges of the steamer (see Figure 5).

5.Go on to Installation Step 3.

Figure 5

 

 

 

 

 

 

 

 

 

 

 

 

Installation on Countertop

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

la

n

t

 

 

 

 

 

 

 

 

 

a

 

 

 

 

 

 

 

 

 

e

 

 

 

 

 

 

 

 

 

S

 

 

 

 

 

 

 

 

 

e

 

 

 

 

 

 

 

 

 

p

 

 

 

 

 

 

 

 

 

y

 

 

 

 

 

 

 

 

 

T

 

 

 

 

 

 

 

 

 

V

 

 

 

 

 

 

 

 

 

T

 

 

 

 

 

 

 

 

 

R

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

STEP 2C: MOUNTING ON CABINET BASE

 

 

 

 

 

 

 

 

 

 

 

 

If the steamer is to be mounted on the optional cabinet base, first attached the legs to the cabinet base (if not already attached). Then place the steamer on top of the cabinet base and line up the threaded holes on the bottom of the steamer with the holes in the cabinet-base top. Secure the steamer to the base with four 3/8-16 bolts. Go on to Installation Step 3.

STEP 2D: STACKING TWO STEAMERS

If two steamers are to be stacked, mount the lower steamer first on either legs (Step 2a), a countertop (Step 2b), or the optional cabinet base (Step 2c). Remove (if present) the four chrome-plated plugs from the holes in the top panel of the lower steamer. Place the upper steamer on top of the lower steamer and line up the threaded holes on the bottom of the upper steamer with the holes in the top of the lower steamer. Secure the upper steamer to the lower steamer with four 3/8-16 bolts. The remaining steps of the installation must be performed for both steamers (they do not share any connections internally).

PAGE 14 OF 48

OWNER’S MANUAL 1185184

Page 13 Page 15
Image 14
Page 13 Page 15
Contents StratoSteam Safety Precautions Introduction Location of Serial PlatesClearances SpecificationsDimensions Dimensions Right Side ViewDrain Requirements Electrical RequirementsWater Requirements Startup Troubleshooting by OperatorOperation OperationControls Cooking TipsSuggested Cooking Times Periodic DE-LIMING AS Needed Cleaning & MaintenanceDaily Cleaning and Maintenance STAINLESS-STEEL SurfacesStratosteam Countertop Steamer Cleaning & Maintenance Installation UnpackingAttach Legs Attach LegsMounting on Cabinet Base Installation on CountertopAttach to Countertop Stacking TWO SteamersLocation of Connections and Vents Drain ConnectionWater Connection Water DrainWater Connection Electrical Connection Electrical ConnectionCheck Steamer Operation Check the InstallationSHUT-DOWN and WIPE-CLEAN Steamer Service Troubleshooting FLOWCHARTS, PROCEDURES, and Wiring DiagramsHOW the Steamer Operates How the Steamer Operates Steamer Not Heating Up, Power Light Is Not Lit Disconnect Power AT Circuit BreakerCheck that water-supply pressure is adequate Buzzer Does Not Come On When Timer Runs Out Disconnect Power AT Circuit Breaker Heating Cartridge Check at ContactorPower Switch Check Contactor Check Timer and Buzzer Check Door Switch Check High-Limit Thermostats Check Water-Level-Control Sensor Check Water Solenoid Check Wiring Diagram for 208/220/240 Volt Models Wiring Diagram for 480 Volt Models Parts Diagram PartsStructural Parts See parts list on previous Door Assembly Parts Door Switch Parts Control Panel Parts Heating Cartridges, Thermostats, and Contactor Parts Water Train Parts Water-Train Parts Cabinet Base Parts Cabinet-Base Parts Stratosteam Countertop Steamer Stratosteam Countertop Steamer StratoSteam Countertop Steamer Models STRE-3D and STRE-5D
Top Page Image Contents