Omega Engineering 30, 48, 20, 25 manual Some frequently asked questions

Page 34

11. Some frequently asked questions

Q1 What is the ‘Pause’ function at the start of the program used for?

A1 Some users prefer to preheat the heated lid before placing the samples into the unit. The pause feature is used to stop the unit a fter the 4 minut e heated lid preheat step. It will also sound an audible alarm indicating that the machine is ready for the sample tubes or pla te to be added. Pressing the “Pause” key followed by the “Enter” key will commence the remaining program.

Q2 Why do you have to press some keys twice to make the unit do what you want it to do?

A2 With many of the program f eatures there is a fail-safe function which asks if you are sure you want to perform a particular action. You are required to press one key to select a function followed by a second to accept it.

Q3 What is ‘Hot Start’?

A3 A “hot start” is used for reducing non-specific product for mation during the first cycle of amplification. The ‘Hot S tart’ programming step is used to pause the instrument at a specific temperature, typically around 70ºC, after the initial template denaturation. The reason is to allow the manual addition of unmodified Taq DNA polymerase which may loose activity if added during the initial 5min denaturation. Heat-activated Taq or Hot Start enzy mes do not require this step.

Q4 What is the incremental function? (See page 24).

A4 Incremental timing and temperature are used to increase or decrease either the time or temperature incrementally over the number of cycles in a stage. Incrementation of extension time is used with ‘Long PCR’ which is when large template fragments are to be amplified (e.g. 27kb lambda DNA, 40kb ge nomic DNA).

Decremental temperature is used for protocols such as ‘Touchdown PCR’ where one starts with a high annealing temperature in the first cycle and gradually decreases the temperature over the numbe r of cycles in the stage. This ensures that only the specific product is amplified.

Q5 The heat-up ramp-rate in the specification is 3.6°C/second yet I can only manually set it to 2.0°C/second. Why is this?

A5 If you set the ramp-rate to max the block will heat at 3.6°C/second the unit sets its own control parameters. If you program a ramp-rate the control parameters reduce the ramp-rate. This is a feature of the software and not the actual ramp- rate.

34

Page 33 Page 35
Image 34
Page 33 Page 35
Contents User’sGuide TCY 20, 25, 30Thermal Cyclers Shop online atServicing North America OMEGAnet Online Service omega.comInternet e-mail info@omega.com For immediate technical or application assistanceContents 1. Introduction 2. Safety and installationOperator Safety Unpacking InstallationReplacement cable ELECTRICIANWorking Conditions Heating/Cooling Rate 3. Cycler TCY SpecificationTemperature Heated LidPower 4. User operation and consumablesDimensions Heated lid0.5ml Tubes to select TCYTCProgramsMethods00 Information ConfigurationPrograms Configuration5. Front panel controls MethodsThe Up arrow key The keysThe End, Finish or Exit key The Down arrow key6. Programming the CYCLER The Alpha/Numeric keysCycle MethodsPrograms00 Information ConfigurationStage StepRun ProgramMethod 2 STEP TEMPLATESTEP Option 1 Creating programs using templatesTo give a program a name To save the programto select DONNA 7 Run programmethod ProgramsMethods00 Information ConfigurationSet password to select To edit a field or step in an existing program72.0ºC Post hold10.0 5m00To set a password for a selected program UNNAMED #10.0ºCºC 105ºCNew*New- program ** 2 STEP TEMPLATE 5012 3 STEP TEMPLATE Example programsProgramming Typical 3-Step PCRto edit the step as To insert additional stepsTo delete a step described aboveTo add a new stage before an existing one to insertstage To add a new stage at the endTo insert a ‘pause’ into a program The prompt line will flash between ‘CHANGE TO PAUSE?’ and ‘YES or NO’Press “Enter” Press “Pause” To program increment or decrement temperature or timeTemperature profile of incremented Hold Time at step 3 of each cycle to go into edit modetwice to go into edit View methodProgram Run ProgrammethodGEORGE Stopping what you are doingto select Run methodProgramNewprogramMethods To run a programHold @ Sample58.0ºC 72.0ºCBlock s/nid 8. Configuration7. Information Unit s/nPasswordsFormat memory ProgramSettingsdefaultsxxxx SettingsSURE ? Thiswill delete Passwords9. Notes on transferring protocols from other thermal cyclers Heater Block removal 10. User maintenanceCleaning your CYCLER Underside of the CYCLER TCY11. Some frequently asked questions Insulation testing 12. Additional informationFault Finding FusesWARRANTY/DISCLAIMER RETURN REQUESTS/INQUIRIESFLOW/LEVEL TEMPERATUREPRESSURE, STRAIN AND FORCE pH/CONDUCTIVITY
Top Page Image Contents