Falcon U109635-02 manual Fitting the Splashback, Fitting the Stability Bracket

Page 25

Australia

INSTALLATION

Check the appliance is electrically safe and gas sound when you have ﬁnished.

Fit the plastic blanking plugs to the ﬁxing holes. Remove the 4mm Allen screws from the top corners of the fascia and ﬁx the front handrail in position.

Fitting the Splashback

The cooker can be installed with or without the supplied splashback. To ﬁt the splashback, remove the two ﬁxing screws (3mm hexagonal socket head) and nuts that pass through the top of the rear ﬂue grille. Hold the splashback in position. From the rear, reﬁt the two ﬁxing screws and nuts.

Fitting the Stability Bracket

The stability bracket supplied with the cooker must be ﬁtted. Read the leaﬂet supplied with the bracket, and ﬁt it as follows:

1.Place the cooker in its intended position and level the cooker.

2.Draw a pencil line 70mm from the front edge of the levelling feet.

3.Mark the centre line for the bracket by measuring 550mm from the left hand side of the cooker.

4.Move the cooker forward.

5.Measure back from the pencil line 500mm to locate the front edge of the bracket. Position the bracket so that it is away from centreline of the cooker to reduce the possibility that it will trap the electrical connection cable or gas hose. Fix the bracket to the ﬂoor.

6.Measure the height from ﬂoor level to the engagement edge at the rear of the cooker. Add 3mm to this dimension and assemble the stability bracket to this height (i.e. from ﬂoor level to the underside of the top member), and ensure the bracket does not foul the oven burner assembly:

25

Image 25

Contents User Guide for Australia Contents Before you start This appliance is heavy, so take care when moving it CleaningCooker Overview Hotplate Burners Griddle High/medium Wok CradleMedium/low Glide-out Grill Never close the grill door when the grill is onLeft Hand Oven OvensRight Hand Tall Oven Timer Setting the time of dayClock To stop the ovens at a specific time of dayAuto is showing, but you want to revert to manual cooking Multi-Function OvenKey Lock Pre-heat this function before cooking Multi-Function Oven FunctionsHandyrack Main Oven Tips on Cooking with the TimerFish Oven Cooking chart Conventional and Fan OvensOven Shelves General Oven TipsLeft Hand Main Oven Main Oven Light Cleaning your CookerHotplate Burners Essential InformationControl Panel and Doors GrillMain Oven Wok CradleTall Oven TroubleshootingHotplate burners will not light Hotplate ignition or hotplate burners faultyIf you have a problem Service and SparesOut of Warranty Please noteInstallation Side clearances Measurements B & C Overhead Measurement aMoving the Cooker Unpacking the CookerLowering the Two Rear Rollers Side clearances Measurement EConversion to LP Repositioning the Cooker following ConnectionLevelling Fitting the Handles and Front HandrailFitting the Stability Bracket Fitting the SplashbackFitting the Restraining Chain Gas ConnectionTap Adjustment Pressure testing for Natural GasConversion from Natural Gas to LP Gas JetsElectrical Connection Propane Pressure TestingStick on label Fitting the Plinth Oven CheckCustomer Care Thank youServicing Notes To Replace the Grill Controller To Replace a ThermostatTo Change a Hotplate Tap To Replace a Hotpate Burner JetTo Change the Main Oven Door Catch To Remove an Oven Inner Back To Change Ignition GeneratorTo Replace an Oven Fan To Replace an Oven Fan ElementTop Element To Adjust the Main Oven Door AngleCircuit Diagram Technical Data Australia Australia Australia