Falcon U109635-02 manual To Replace a Thermostat, To Replace the Grill Controller

Page 31

Australia

SERVICING - WARNING

Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.

7. To Replace a Thermostat

Remove the control panel (see section 2) and hotplate top (see section 3). Open the appropriate oven door and remove the oven shelves.

thumb and forefinger. Pull off the electrode, but keep hold of the lead. Fit the new electrode to the lead. Fix the electrode in the burner with the screw. Replace the burner cap. Check the burner ignition. Replace the pan supports.

Right hand oven

Remove the oven roof. Remove the two fixings that secure the thermostat phial cover. Unclip the thermostat phial from the clips in the oven back panel and remove it from the top rear of the oven.

Left hand oven

Remove the two screws holding the thermostat phial to the oven fan cover at the rear of the oven. Pull the unit forward to access the rear of the cooker. Remove both rear cover boxes by removing the fixing screws and lifting clear.

Feed the thermostat capillary clear of the oven. Disconnect the wires from the thermostat and undo the two fixings that secure the control to the mounting plate. Fit the replacement and re-assemble in reverse order. Ensure that the phial is clipped to the oven rear, positioned centrally between the clips. Check that the thermostat functions correctly.

8. To Replace the Grill Controller

Remove the control panel (see section 2) and hotplate top (see section 3). Disconnect the wiring from the controller. Remove the two screws holding the switch/controller to mounting panel. Fit the new controller and re-assemble in reverse order. Check for correct operation.

9. To Change a Hotplate Tap

Remove the hotplate top (see section 3). Unplug the FSD lead from the rear of the tap. Undo the compression fitting at the rear of the tap. Remove the fixings that secure the tap to the gas rail. Remove the tap. Remove and discard the gasket seal. Fit the new gasket seal to the replacement tap. Re-assemble in reverse order.

Ensure that the valve is adjusted for correct gas operation. Check that the cooker is gas sound. Check hotplate ignition.

10. To Replace a Hotpate Burner Jet

Remove the burner cap and head. Remove the old jet. Fit the new orifice.

NB The Wok burner has 2 orifices.

Re-assemble in reverse order. Check that the appliance is gas sound.

11. To Change a Hotplate Burner Electrode

Lift off the cooktop pan supports and remove the burner cap. Remove the screw holding the electrode. Pull the electrode vertically up sufficiently to grip the lead between

12. To Remove or Change a Hotplate Burner.

Remove the hotplate top (see section 3). Remove the control panel (see section 2).

Outer Hotplate Burners

The burners are mounted in two’s on cross supports. Disconnect the burner feed pipes at the burners. Remove the screw at the front holding the cross support. Slide the support to the right to release it from the rear location.

Lift the cross support and burners clear. The burners are fixed to the cross supports with screws underneath. Remove the appropriate burner and fit the new one.

Re-assemble in reverse order. Check that the burner operation is satisfactory.

Wok burners

Disconnect the burner feed pipes at the burner. Fit the new one and re-assemble in reverse order. Check that the burner operation is satisfactory.

13. To Remove the Grill Outer Door Panel

Open the left hand oven door and remove the two screws from the bottom edge of the grill door.

Open the grill door, support grill door outer panel, and remove the two screws from the top inner face of the grill door.

Re-assemble in reverse order.

14. To Remove an Oven Door

Open the oven door and remove the Handyrack (where fitted) by springing one side out of the bracket on the door and sliding the other side free. The door is heavy - take care. Open the oven door and loosen the two top hinge screws.

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents User Guide for Australia Contents Before you start This appliance is heavy, so take care when moving it CleaningCooker Overview Hotplate Burners Griddle High/medium Wok CradleMedium/low Glide-out Grill Never close the grill door when the grill is onLeft Hand Oven OvensRight Hand Tall Oven To stop the ovens at a specific time of day Setting the time of dayTimer ClockAuto is showing, but you want to revert to manual cooking Multi-Function OvenKey Lock Pre-heat this function before cooking Multi-Function Oven FunctionsHandyrack Main Oven Tips on Cooking with the TimerFish Oven Cooking chart Conventional and Fan OvensOven Shelves General Oven TipsLeft Hand Main Oven Essential Information Cleaning your CookerMain Oven Light Hotplate BurnersWok Cradle GrillControl Panel and Doors Main OvenTall Oven TroubleshootingHotplate burners will not light Hotplate ignition or hotplate burners faultyPlease note Service and SparesIf you have a problem Out of WarrantyInstallation Side clearances Measurements B & C Overhead Measurement aSide clearances Measurement E Unpacking the CookerMoving the Cooker Lowering the Two Rear RollersFitting the Handles and Front Handrail Repositioning the Cooker following ConnectionConversion to LP LevellingFitting the Stability Bracket Fitting the SplashbackFitting the Restraining Chain Gas ConnectionJets Pressure testing for Natural GasTap Adjustment Conversion from Natural Gas to LP GasElectrical Connection Propane Pressure TestingStick on label Thank you Oven CheckFitting the Plinth Customer CareServicing Notes To Replace a Hotpate Burner Jet To Replace a ThermostatTo Replace the Grill Controller To Change a Hotplate TapTo Change the Main Oven Door Catch To Replace an Oven Fan Element To Change Ignition GeneratorTo Remove an Oven Inner Back To Replace an Oven FanTop Element To Adjust the Main Oven Door AngleCircuit Diagram Technical Data Australia Australia Australia
Top Page Image Contents