Falcon U109635-02 manual Servicing Notes

Page 30

Australia

SERVICING - WARNING

Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.

Servicing Notes

Before servicing or replacing gas carrying components, disconnect the cooker from the gas supply, and check that the appliance is gas sound following completion.

Likewise, before servicing or replacing components that are connected to the electricity supply, particularly before removing the control panel, side panels, cooktop tray, or any of the electrical components or cover boxes, disconnect the cooker from this supply, and check that the appliance is electrically safe prior to reconnection.

CAUTION: DO NOT USE A FLAME TO CHECK FOR GAS LEAKS.

1. To Remove the Hand Rail

Remove the handrail plastic blanking plugs and remove the two end bracket fixing screws.

2. To Remove the Control Panel

Pull off all the control knobs. Remove the hand rail (see section 1) Remove the two cross headed screws that were hidden by the hand rail end brackets.

Open the grill door and right hand oven door and remove the two screws underneath the control panel.

Pull the control panel forward and support so that the wires are not strained.

Re-assemble in reverse order. When replacing leads, refer to the wiring diagram. Check the operation of the timer, ignition, and oven light switches.

3. To Remove the Hotplate Top

Remove the pan supports, cooktop burner caps and tops. If there are screws holding the cooktop burners to the cooktop, remove them (but not the spark electrode fixing screws).

A Cooktop front fixing screws

BCooktop rear fixing screws (on cooker back)

Remove the two rear cooktop fixing screws (B) on the cooker back under the flue grille, and the four front cooktop fixing screws (A).

Remove the screws holding the flue grille stays.

Lift the cooktop clear of the appliance. Replace in reverse order.

Re-assemble in reverse order, ensuring that the leads are reconnected.

Check for correct burner operation.

4. To Remove a Side Panel

Remove the control panel (see section 2). Pull the cooker forward. Remove the four retaining screws from each panel (two at the front and two at the rear). The lower front retaining screws (one each side) are situated beneath the lower edge at the front corners of the side panels

Re-assemble in reverse order.

5. To Replace the Main Oven Light Switch

Remove the control panel (see section 2).

NB The old switch may be destroyed during removal.

Remove the switch button and old switch from its bezel by gripping the switch body behind the control panel and twisting sharply.

The switch bezel can then be removed by folding back its locking wings and pushing forward. Fit the new bezel to the control panel by first lining up the raised key on its body with the cutout in the control panel and pushing it in from the front. Assemble the new switch to the bezel by lining up the key sections and pushing home. Fit the new button by pushing in from the front.

Replace the control panel and test for correct operation.

6. To Replace the Electronic Timer

Pull off the timer control buttons and remove the control panel (see section 2). Remove the timer/mounting bracket assembly from the control panel by removing the two fixing screws. Remove the timer from its mounting bracket by depressing the plastic lugs on the timer case, at the same time pulling the unit forward.

Re-assemble in reverse order. When replacing the leads, refer to the wiring diagram. Check the operation of the timer.

30

Page 29 Page 31
Image 30
Page 29 Page 31
Contents User Guide for Australia Contents Before you start Cleaning This appliance is heavy, so take care when moving itCooker Overview Hotplate Burners Griddle Wok Cradle High/mediumMedium/low Never close the grill door when the grill is on Glide-out GrillOvens Left Hand OvenRight Hand Tall Oven Clock Setting the time of dayTimer To stop the ovens at a specific time of dayMulti-Function Oven Auto is showing, but you want to revert to manual cookingKey Lock Multi-Function Oven Functions Pre-heat this function before cookingTips on Cooking with the Timer Handyrack Main OvenOven Cooking chart Conventional and Fan Ovens FishGeneral Oven Tips Oven ShelvesLeft Hand Main Oven Hotplate Burners Cleaning your CookerMain Oven Light Essential InformationMain Oven GrillControl Panel and Doors Wok CradleTroubleshooting Tall OvenHotplate ignition or hotplate burners faulty Hotplate burners will not lightOut of Warranty Service and SparesIf you have a problem Please noteInstallation Overhead Measurement a Side clearances Measurements B & CLowering the Two Rear Rollers Unpacking the CookerMoving the Cooker Side clearances Measurement ELevelling Repositioning the Cooker following ConnectionConversion to LP Fitting the Handles and Front HandrailFitting the Splashback Fitting the Stability BracketGas Connection Fitting the Restraining ChainConversion from Natural Gas to LP Gas Pressure testing for Natural GasTap Adjustment JetsPropane Pressure Testing Electrical ConnectionStick on label Customer Care Oven CheckFitting the Plinth Thank youServicing Notes To Change a Hotplate Tap To Replace a ThermostatTo Replace the Grill Controller To Replace a Hotpate Burner JetTo Change the Main Oven Door Catch To Replace an Oven Fan To Change Ignition GeneratorTo Remove an Oven Inner Back To Replace an Oven Fan ElementTo Adjust the Main Oven Door Angle Top ElementCircuit Diagram Technical Data Australia Australia Australia
Top Page Image Contents