Falcon U109635-02 manual To Change the Main Oven Door Catch

Page 32

Australia

SERVICING - WARNING

Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.

Support the weight of the door and remove the screw nearest the hinge pin. Swing the hinge up and away from the hinge pin on the door.

Lift the door away from the bottom hinge. Re-assemble in reverse order.

When replacing the door, ensure that the nylon hinge bush is in position between the hinge pin and the hinge bracket at the both the bottom and top.

15. To Change the Main Oven Door Outer Panel

Remove the two plastic blanking plugs from the door handles. Remove the four 4mm Hex headed screws holding the handle to the door with the hexagon key tool. Remove two screws from the top edge, and two from the bottom edge, of the door:

Remove the outer door panel. Fit the door handle to the new panel. Fit the plastic blanking plugs to the fixing holes.

The handles should be above the fixings.

Fit the panel to the door. If replacing the outer panel on the right hand door (with the Thermodial) take care to make sure that the sensor of the Thermodial is sealed to the door by the rubber grommet:

16. To Change the Main Oven Door Catch

Remove the outer door panel (see section 15). Remove screws ‘B’ holding the catch assembly to the inner door panel. Fit the new catch and re-assemble in reverse order.

Verify that the door operation is correct.

17. To Adjust the Main Oven Door Catch Keep

Open the Main oven door, slacken off the locknut at the base of keep, and screw in or out as required until the required fit is obtained:

Retighten the locking nut.

18.To Replace the Tall Oven Door Outer Panel

Remove the oven door (see section 14). Lay the door face down on a suitable surface and remove the two screws from the bottom edge of door and the two screws from the inside face of the door.

Remove the outer door panel. Remove the door handle by unscrewing the two screws.

Remove the two cross-headed screws holding the door handle fixing bracket to the door panel. Fit the door handle bracket and the door handle to the new panel.

Fit the panel to the door and re-assemble in reverse order.

19. To Replace the Tall Oven Door Magnetic Latch

Remove the control panel (see section 2). Remove the plinth (three screws) and the central vertical cover (five screws). Prize the retaining clip off the magnet unit.

Fit the new unit and retaining clip, and re-assemble in reverse order. Verify that the door operation is correct.

20. To Change an Oven Door Seal

Open the oven door. The seal is held in place by small hooks on the rear face. At the corner, pull the seal diagonally away from the door centre until that hook is released. Proceed to

the next hook and release it in a similar way, and so on.

Re-assemble in reverse order.

32

Page 31 Page 33
Image 32
Page 31 Page 33
Contents User Guide for Australia Contents Before you start Cleaning This appliance is heavy, so take care when moving itCooker Overview Hotplate Burners Griddle Medium/low Wok CradleHigh/medium Never close the grill door when the grill is on Glide-out GrillRight Hand Tall Oven OvensLeft Hand Oven Setting the time of day TimerClock To stop the ovens at a specific time of dayKey Lock Multi-Function OvenAuto is showing, but you want to revert to manual cooking Multi-Function Oven Functions Pre-heat this function before cookingTips on Cooking with the Timer Handyrack Main OvenOven Cooking chart Conventional and Fan Ovens FishLeft Hand Main Oven General Oven TipsOven Shelves Cleaning your Cooker Main Oven LightHotplate Burners Essential InformationGrill Control Panel and DoorsMain Oven Wok CradleTroubleshooting Tall OvenHotplate ignition or hotplate burners faulty Hotplate burners will not lightService and Spares If you have a problemOut of Warranty Please noteInstallation Overhead Measurement a Side clearances Measurements B & CUnpacking the Cooker Moving the CookerLowering the Two Rear Rollers Side clearances Measurement ERepositioning the Cooker following Connection Conversion to LPLevelling Fitting the Handles and Front HandrailFitting the Splashback Fitting the Stability BracketGas Connection Fitting the Restraining ChainPressure testing for Natural Gas Tap AdjustmentConversion from Natural Gas to LP Gas JetsStick on label Propane Pressure TestingElectrical Connection Oven Check Fitting the PlinthCustomer Care Thank youServicing Notes To Replace a Thermostat To Replace the Grill ControllerTo Change a Hotplate Tap To Replace a Hotpate Burner JetTo Change the Main Oven Door Catch To Change Ignition Generator To Remove an Oven Inner BackTo Replace an Oven Fan To Replace an Oven Fan ElementTo Adjust the Main Oven Door Angle Top ElementCircuit Diagram Technical Data Australia Australia Australia
Top Page Image Contents