Falcon U109635-02 manual Electrical Connection, Stick on label, Propane Pressure Testing

Page 28

Australia

INSTALLATION

Check the appliance is electrically safe and gas sound when you have finished.

Electrical Connection

�

To convert the governor, snap the device out of the top and refit it the other way up. The snap-in converter device is marked to show the gas for which it is set:

Natural gas

 

 

 

 

Propane gas

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

This appliance must be installed by a qualified electrician to comply with the relevant regulations (in particular AS/NZS 60335.2.6:2002), and also the local electricity supply company requirements.

Make sure the device is secure in the top cap and refit the cap to the governor.

Stick on label

Stick the appropriate label on to the data badge to indicate the gas for which the appliance is now set.

Propane Pressure Testing

Connect the appliance to the gas supply. Ensure that the appliance is gas sound.

The gas pressure can be measured at one of the left hand hotplate burner jets. Lift off a burner head. Fit the pressure gauge to the jet. Turn on the hotplate burner and turn on and light one of the other burners.

Re-assemble the burner top, making sure that it is re- assembled in the correct way on the burner body.

Refit the control tap shield. Reconnect the wiring to the control panel and refit the panel.

Check that the appliance is both electrically safe and gas sound.

Check the operation of all the burners.

Ensure that the mains characteristics (voltage, nominal, power, etc.) match the ratings indicated on the data plate affixed to the cooker.

The cooker is preset for a single-phase earthed electrical connection. It is essential to install a multi-pole circuit breaker that completely disconnects the appliance from the mains, with a minimum contact break distance of 3mm.

WARNING: THIS APPLIANCE MUST BE EARTHED

The appliance must be connected to an efficient earthing circuit. If the electricity network is not equipped with an earth connection, then it must be installed separately in compliance with local regulations.

Earthing is a safety measure required by law, and must be performed with particular care by a qualified technician, who must also check that the electricity supply characteristics are correct.

The cable size used should be suitable for the appliance load and in accordance with local regulations. Please note that the maximum cable sizes are 6mm2 for the screw terminals.

Access to the mains terminal is gained by removing the electrical terminal cover box on the back panel. Connect the mains cable to the correct terminals for your electrical supply type.

You may need to move the links to suit your connection type. Check that the links are correctly fitted and that the terminal screws are tight. Secure the mains cable using the cable clamp.

28

Page 27 Page 29
Image 28
Page 27 Page 29
Contents User Guide for Australia Contents Before you start Cleaning This appliance is heavy, so take care when moving itCooker Overview Hotplate Burners Griddle High/medium Wok CradleMedium/low Never close the grill door when the grill is on Glide-out GrillLeft Hand Oven OvensRight Hand Tall Oven Setting the time of day TimerClock To stop the ovens at a specific time of dayAuto is showing, but you want to revert to manual cooking Multi-Function OvenKey Lock Multi-Function Oven Functions Pre-heat this function before cookingTips on Cooking with the Timer Handyrack Main OvenOven Cooking chart Conventional and Fan Ovens FishOven Shelves General Oven TipsLeft Hand Main Oven Cleaning your Cooker Main Oven LightHotplate Burners Essential InformationGrill Control Panel and DoorsMain Oven Wok CradleTroubleshooting Tall OvenHotplate ignition or hotplate burners faulty Hotplate burners will not lightService and Spares If you have a problemOut of Warranty Please noteInstallation Overhead Measurement a Side clearances Measurements B & CUnpacking the Cooker Moving the CookerLowering the Two Rear Rollers Side clearances Measurement ERepositioning the Cooker following Connection Conversion to LPLevelling Fitting the Handles and Front HandrailFitting the Splashback Fitting the Stability BracketGas Connection Fitting the Restraining ChainPressure testing for Natural Gas Tap AdjustmentConversion from Natural Gas to LP Gas JetsElectrical Connection Propane Pressure TestingStick on label Oven Check Fitting the PlinthCustomer Care Thank youServicing Notes To Replace a Thermostat To Replace the Grill ControllerTo Change a Hotplate Tap To Replace a Hotpate Burner JetTo Change the Main Oven Door Catch To Change Ignition Generator To Remove an Oven Inner BackTo Replace an Oven Fan To Replace an Oven Fan ElementTo Adjust the Main Oven Door Angle Top ElementCircuit Diagram Technical Data Australia Australia Australia
Top Page Image Contents