Makita EM2650UH, EM2650LH manual Procedure Interval

Page 27

(2)Air Induction System

(i)Air cleaner plate (including choke system)

(ii)Air cleaner cover

(iii)Air cleaner element

(3)Ignition System

(i)Spark Plugs.

(ii)Magneto or electronic ignition system.

(iii)Spark advance/retard system.

(4)Miscellaneous Items Used in Above Systems

(i)Hoses, Sealing gaskets, belts, connectors, and assemblies.

Makita USA, Inc will furnish with each new engine written instructions for the maintenance and use of the engine by the owner.

(e)MAINTENANCE STATEMENTS

It is your responsibility to have all scheduled inspection and maintenance services performed at the times recommended in the 2007 and later Owner’s Manual and to retain proof that inspection and maintenance services are performed at the times when recommended. Makita USA, Inc will not deny a warranty claim solely because you have no record of maintenance; however, Makita USA, Inc may deny a warranty claim if your failure to perform required maintenance resulted in the failure of warranted part. The proof, which you maintain, should be given to each subsequent owner of the engine. You are responsible for performing the scheduled maintenance described below based on the procedures speciﬁed in the 2007 and later Owner’s Manual. The scheduled maintenance below is based on the normal engine-operating schedule.

	PROCEDURE	INTERVAL
1)	Clean engine and check bolts and nuts. Retighten if	: Every 8 hours (daily)
	necessary.
2)	Check and reﬁll engine oil (4 stroke engine only)	: Every 8 hours (reﬁll daily up to upper limit)
3)	Change engine oil (4 stroke engine only)	: Initial 20 hours and every 50 hours afterward
4)	Check clogging of cooling air passage and cylinder	: Every 8 hours (daily)
	ﬁns. Remove and clean if necessary.

5)Clean air cleaner.

6)Check spark plug. Clean and adjust if necessary.

7)Check mufﬂer exhaust outlet (or port). Clean if necessary.

:Every 8 hours (daily)

:Every 8 hours (daily)

:Every 50 hours (monthly)

8)Check fuel ﬁlter. If clogged, replace with new one.

9)Adjust valve clearance, if applicable (4 stroke engine only).

:Every 50 hours (monthly)

:Every 200 hours (yearly)

10)	Replace fuel lines.	: Every 200 hours (yearly)
11) Clean and inspect the complete engine. Replace		: Every 200 hours
	any damaged or worn out parts.
12)	Replace packings and gaskets with new ones.	: Every reassembling

27

Image 27

Contents Importante EM2650UH EM2650LHTable of Contents SymbolsPersonal protective equipment Safety InstructionsGeneral Instructions Intended use of the machineRefueling Resting Transport Refueling Maintenance Tool replacementKickback Maintenance instructionsMethod of operation Cutting ToolsWhen asking for help, please give the following information Never straighten or weld damaged cutting toolsFirst Aid Model EM2650UH EM2650LH Technical Data EM2650UH, EM2650LHEM2650UH Designation of PartsMounting of Handle For machines with bike handle modelsFor machines with loop handle Use of nylon cutting head EM2650UH, EM2650LH Use of metal blade EM2650UH, optional accessory for EM2650LHMounting of Protector For EM2650UHFor EM2650LH Mounting of Cutter Blade or Nylon Cutting Head Mounting of cutterblade with the hex wrench still in placeMounting of nylon cutting head Inspection and reﬁll of engine oil Point 1 in Replacement of oil Oil capOil volume Before Start of OperationFuel RefuelingHandling of fuel Storage period of fuelPoints in Operation and HOW to Stop Correct Handling of MachineStarting Startup after warm-up operation At times, such as winter, when starting the engineCheckup of LOW-SPEED Rotation Adjustment of LOW-SPEED Rotation IdlingResharpening the Cutting Tool StoppingReplacing the nylon cord Daily checkup and maintenance Replacement of Engine OILServicing Instructions Cleaning of AIR Cleaner Points in Handling Air Cleaner ElementPoints on OIL Replacement of Gaskets and Packings Cleaning of Fuel FilterReplacement of Fuel Pipe Cleaning of PartsFault location Fault System Observation CauseStorage 30h 200h Operating time BeforeDaily 50h Shutdown OperationBlade TroubleshootingState of abnormality Probable cause malfunction Remedy Starts. Once engine starts, cutter bladeEmission Compliance Period MANUFACTURER’S Warranty Coverage Procedure Interval Parts Covered Emission Component Defect Warranty PeriodObtaining Warranty Service What is not CoveredOWNER’S Warranty Responsibilities HOW to Make a Claim Table des matières PictogrammesÉquipement de protection personnel Consignes DE SécuritéConsignes générales Utilisation normale de la machineRemplissage Pause Transport Remplissage Entretien Remplacement d’outilPrévention des mouvements de recul Mode de fonctionnementOutils de coupe Mouvement de reculPremiers soins Modèle EM2650UH EM2650LH Données Techniques EM2650UH, EM2650LHDésignation DES Pièces Désignation DES PiècesMontage DE LA Poignée Pour les machines avec guidonPour les machines avec poignée arceau Poignée Sangle Utilisation d’une tête à ﬁls nylon EM2650UH, EM2650LHMontage DU Protecteur Pour le EM2650UHPour le EM2650LH Montage DE LA Lame DE Coupe OU DE LA Tête À Fils Nylon MakitaMontage de la tête à ﬁls nylon Avant Utilisation Inspection et remplissage de l’huile moteurQuantité d’huile Environ 0,08 l Carburant RemplissageManipulation de l’essence Entreposage de l’essenceDémarrage Manipulation Correcte DE LA MachineFixation de la sangle d’épaule DétachementPendant les périodes, telles que l’hiver, où Démarrage après le réchauffageVérification DE LA Rotation À Faible Vitesse Réaffûtage DE L’OUTIL DE CoupeArrêt Réglage DE LA Rotation À Faible Vitesse RalentiRemplacement du ﬁl nylon Vériﬁcation et entretien quotidiens Remplacement DE L’HUILE MoteurHuile recommandée Instructions D’ENTRETIENNettoyage DU Filtre À AIR Remarques Concernant L’HUILELubrification DU Carter D’ENGRENAGE Remplacement DU Tuyau D’ALIMENTATION EN EssenceRemplacement DES Joints ET Garnitures Vérification DE LA Bougie D’ALLUMAGEEmplacement des défaillances EntreposageDéfaillance Système Observation Cause Pause Quotidien FonctionnementArrêt 30 h 50 h 200 hLame de coupe commence. Faites très Anomalie Cause probable dysfonctionnement SolutionDépannage Fois le moteur démarré, la rotation de laÍndicePágina SímbolosEquipo protector personal Instrucciones DE SeguridadInstrucciones generales Uso intencionado de la herramientaResuministro de combustible Prevención de retrocesos bruscos Método de operaciónPiezas cortadoras Retrocesos bruscosPrimeros auxilios Modelo EM2650UH EM2650LH Especificaciones Técnicas EM2650UH, EM2650LHIdentificación DE LAS Piezas Identificación DE LAS PiezasColocación DEL Mango Para modelos equipados con mango tipo bicicletaPara modelos equipados con mango tipo redondo Uso de la cabeza cortadora de nailon EM2650UH, EM2650LH Colocación DEL Protector Para EM2650UHPara EM2650LH Colocación de la cabeza cortadora de nailon Colocación DEL Disco Cortador O Cabeza Cortadora DE NailonPunto 1 en el reemplazo del aceite Tapa del aceite Volumen de aceite Aprox ,08LAntes DE Iniciar LA Operación Inspeccione y resuministre el aceite del motorCombustible Reabastecimiento DE CombustibleManejo del combustible Periodo de almacenamiento del combustibleManejo Correcto DEL Equipo Puntos EN LA Operación Y Cómo Detener LA OperaciónArranque DEL Motor En ciertas ocasiones, como en el invierno, cuando Arranque tras la operación de calentamientoRevisión DE LA Rotación DE Baja Velocidad Reafilado DE LA Pieza CortadoraParo DE LA Operación Ajuste DE LA Rotación DE Baja Velocidad Estado PasivoReemplazo del cordón de nailon Instrucciones DE Servicio Revisión y mantenimiento diariosReemplazo DEL Aceite DEL Motor Puntos Sobre EL Aceite Limpieza DEL Filtro DE AirePuntos en el manejo del elemento del ﬁltro de aire Limpieza DE LAS Piezas Engrasado DE LA Caja DE CambiosRevisión DE LA Bujía DE Encendido Inspección DE PERNOS, Tuercas Y TornillosDeterminación de fallas AlmacenamientoAtención Atención tras el almacenamiento de largo plazo30h 50h 200h Antes Tras la DiarioAcción OperaciónResolución DE Problemas Estado de anomalía Causa probable falla SoluciónCortador Periodo DE Conformidad Sobre Emisiones Cobertura DE LA Garantía DEL Fabricante Intervalo ProcedimientoPiezas Cubiertas Periodo DE Garantía POR Defectos DE Componentes DE EmisionesObtención DE Servicio DE Garantía LO QUE no Está CubiertoResponsabilidades DEL Propietario Para LA Garantía Cómo Preparar UNA Reclamación Page Advertencia