Makita EM2650UH, EM2650LH manual Method of operation, Cutting Tools, Kickback prevention

Page 5

Method of operation

–Only use in good light and visibility. During the winter season beware of slippery or wet areas, ice and snow (risk of slipping). Always ensure a safe footing.

–Never cut above waist height.

–Never stand on a ladder.

–Never climb up into trees to perform cutting operation.

–Never work on unstable surfaces.

–Remove sand, stones, nails etc. found within the working range. Foreign particles may damage the cutting tool and can cause dangerous kick-backs.

–Before commencing cutting, the cutting tool must have reached full working speed.

–When using metal blades, swing the tool evenly in half-circle from right to left, like using a scythe.

Cutting Tools

–Use an applicable cutting tool for the job in hand.

Nylon cutting heads (nylon line) are suitable for trimming lawn grass. Metal blades are suitable for cutting weeds, high grasses, bushes, shrubs, underwood, thicket, and the like.

–When using metal blades, always use the approved protector, handle (with barrier bar) and harness for use of metal blades. Otherwise blade contact may cause serious injury. See the section “Approved combination of cutting tool, protector, handle and harness.”

–When using metal blades, avoid “kickback” and always prepare for an accidental kickback. See the section “Kickback” and “Kickback prevention.”

Kickback

–When operating the Brushcutter, uncontrolled kickback may occur.

–This is particularly the case when attempting to cut within a blade segment between 12 and 2 o’clock.

–Never apply the Brushcutter within a segment between 12 and 2 o’clock.

–Never apply this segment of the Brushcutter blade to solids, such as bushes and trees, etc., having a diameter in excess of 3 cm or the Brushcutter will be deflected at great force with the risk of injuries.

Kickback prevention

To avoid kickbacks, observe the following:

–Operating 12 and 2 o’clock presents a hazard, especially when using metal blades.

–Cutting 11 and 12 o’clock, and between 2 and 5 o’clock, must be performed by trained and experienced operators, and then only at their own risk. Easy cutting with almost no kickback is possible between 8 and 11 o’clock.

Maintenance instructions

–The condition of the cutter, in particular of the cutting tool of the protective devices and also of the shoulder strap must be checked before commencing work. Particular attention is to be paid to the cutting blades which must be correctly sharpened.

–Turn off the engine and remove spark plug connector when replacing or sharpening cutting tools, and also when cleaning the cutter or cutting tool.

Caution:

Kickback

Diagrammatic figure

Diagrammatic figure

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Importante EM2650UH EM2650LHTable of Contents SymbolsGeneral Instructions Safety InstructionsIntended use of the machine Personal protective equipmentRefueling Resting Transport Refueling Maintenance Tool replacementMethod of operation Maintenance instructionsCutting Tools KickbackFirst Aid When asking for help, please give the following informationNever straighten or weld damaged cutting tools Model EM2650UH EM2650LH Technical Data EM2650UH, EM2650LHEM2650UH Designation of PartsFor machines with loop handle Mounting of HandleFor machines with bike handle models Use of nylon cutting head EM2650UH, EM2650LH Use of metal blade EM2650UH, optional accessory for EM2650LHFor EM2650LH Mounting of ProtectorFor EM2650UH Mounting of nylon cutting head Mounting of Cutter Blade or Nylon Cutting HeadMounting of cutterblade with the hex wrench still in place Oil volume Point 1 in Replacement of oil Oil capBefore Start of Operation Inspection and refill of engine oilHandling of fuel RefuelingStorage period of fuel FuelStarting Points in Operation and HOW to StopCorrect Handling of Machine Startup after warm-up operation At times, such as winter, when starting the engineResharpening the Cutting Tool Adjustment of LOW-SPEED Rotation IdlingStopping Checkup of LOW-SPEED RotationReplacing the nylon cord Servicing Instructions Daily checkup and maintenanceReplacement of Engine OIL Points on OIL Cleaning of AIR CleanerPoints in Handling Air Cleaner Element Replacement of Fuel Pipe Cleaning of Fuel FilterCleaning of Parts Replacement of Gaskets and PackingsStorage Fault locationFault System Observation Cause Daily 50h Shutdown Operating time BeforeOperation 30h 200hState of abnormality Probable cause malfunction Remedy TroubleshootingStarts. Once engine starts, cutter blade BladeEmission Compliance Period MANUFACTURER’S Warranty Coverage Procedure Interval Parts Covered Emission Component Defect Warranty PeriodOWNER’S Warranty Responsibilities Obtaining Warranty ServiceWhat is not Covered HOW to Make a Claim Table des matières PictogrammesConsignes générales Consignes DE SécuritéUtilisation normale de la machine Équipement de protection personnelRemplissage Pause Transport Remplissage Entretien Remplacement d’outilOutils de coupe Mode de fonctionnementMouvement de recul Prévention des mouvements de reculPremiers soins Modèle EM2650UH EM2650LH Données Techniques EM2650UH, EM2650LHDésignation DES Pièces Désignation DES PiècesPour les machines avec poignée arceau Montage DE LA PoignéePour les machines avec guidon Poignée Sangle Utilisation d’une tête à fils nylon EM2650UH, EM2650LHPour le EM2650LH Montage DU ProtecteurPour le EM2650UH Montage de la tête à fils nylon Montage DE LA Lame DE Coupe OU DE LA Tête À Fils NylonMakita Quantité d’huile Environ 0,08 l Avant UtilisationInspection et remplissage de l’huile moteur Manipulation de l’essence RemplissageEntreposage de l’essence CarburantFixation de la sangle d’épaule Manipulation Correcte DE LA MachineDétachement DémarragePendant les périodes, telles que l’hiver, où Démarrage après le réchauffageArrêt Réaffûtage DE L’OUTIL DE CoupeRéglage DE LA Rotation À Faible Vitesse Ralenti Vérification DE LA Rotation À Faible VitesseRemplacement du fil nylon Huile recommandée Remplacement DE L’HUILE MoteurInstructions D’ENTRETIEN Vérification et entretien quotidiensNettoyage DU Filtre À AIR Remarques Concernant L’HUILERemplacement DES Joints ET Garnitures Remplacement DU Tuyau D’ALIMENTATION EN EssenceVérification DE LA Bougie D’ALLUMAGE Lubrification DU Carter D’ENGRENAGEDéfaillance Système Observation Cause Emplacement des défaillancesEntreposage Arrêt Quotidien Fonctionnement30 h 50 h 200 h PauseDépannage Anomalie Cause probable dysfonctionnement SolutionFois le moteur démarré, la rotation de la Lame de coupe commence. Faites trèsÍndicePágina SímbolosInstrucciones generales Instrucciones DE SeguridadUso intencionado de la herramienta Equipo protector personalResuministro de combustible Piezas cortadoras Método de operaciónRetrocesos bruscos Prevención de retrocesos bruscosPrimeros auxilios Modelo EM2650UH EM2650LH Especificaciones Técnicas EM2650UH, EM2650LHIdentificación DE LAS Piezas Identificación DE LAS PiezasPara modelos equipados con mango tipo redondo Colocación DEL MangoPara modelos equipados con mango tipo bicicleta Uso de la cabeza cortadora de nailon EM2650UH, EM2650LH Para EM2650LH Colocación DEL ProtectorPara EM2650UH Colocación de la cabeza cortadora de nailon Colocación DEL Disco Cortador O Cabeza Cortadora DE NailonAntes DE Iniciar LA Operación Volumen de aceite Aprox ,08LInspeccione y resuministre el aceite del motor Punto 1 en el reemplazo del aceite Tapa del aceiteManejo del combustible Reabastecimiento DE CombustiblePeriodo de almacenamiento del combustible CombustibleArranque DEL Motor Manejo Correcto DEL EquipoPuntos EN LA Operación Y Cómo Detener LA Operación En ciertas ocasiones, como en el invierno, cuando Arranque tras la operación de calentamientoParo DE LA Operación Reafilado DE LA Pieza CortadoraAjuste DE LA Rotación DE Baja Velocidad Estado Pasivo Revisión DE LA Rotación DE Baja VelocidadReemplazo del cordón de nailon Reemplazo DEL Aceite DEL Motor Instrucciones DE ServicioRevisión y mantenimiento diarios Puntos en el manejo del elemento del filtro de aire Puntos Sobre EL AceiteLimpieza DEL Filtro DE Aire Revisión DE LA Bujía DE Encendido Engrasado DE LA Caja DE CambiosInspección DE PERNOS, Tuercas Y Tornillos Limpieza DE LAS PiezasAtención AlmacenamientoAtención tras el almacenamiento de largo plazo Determinación de fallasAcción Antes Tras la DiarioOperación 30h 50h 200hCortador Resolución DE ProblemasEstado de anomalía Causa probable falla Solución Periodo DE Conformidad Sobre Emisiones Cobertura DE LA Garantía DEL Fabricante Intervalo ProcedimientoPiezas Cubiertas Periodo DE Garantía POR Defectos DE Componentes DE EmisionesResponsabilidades DEL Propietario Para LA Garantía Obtención DE Servicio DE GarantíaLO QUE no Está Cubierto Cómo Preparar UNA Reclamación Page Advertencia
Top Page Image Contents