Makita EM2650LH Mounting of Cutter Blade or Nylon Cutting Head, Mounting of nylon cutting head

Page 12

MOUNTING OF CUTTER BLADE OR NYLON CUTTING HEAD

Be sure to use genuine MAKITA cutter blades or nylon cutting head.

–The cutter blade must be well polished, free of cracks or breakage. If the cutter blade hits against a stone during operation, stop the engine and check the blade immediately.

–Polish or replace the cutter blade every three hours of operation.

–If the nylon cutting head hits against a stone during operation, stop the engine and check the nylon cutting head immediately.

CAUTION: The appropriate protector must always be installed, for your own safety and in order to comply with accident-prevention regulations. Operation of the equipment without the guard being in place is not permitted.

The outside diameter of the cutter blade must be 230 mm (9 - 1/16”). Never use any blades surpassing 230 mm (9 - 1/16”) in outside diameter.

Turn the machine upside down, and you can replace the cutter blade or nylon cutting head easily.

–Insert the hex wrench through the hole in the gear case and rotate the receiver washer (4) until it is locked with the hex wrench.

–Loosen the nut (1) (left-hand thread) with the socket wrench and remove the nut (1), cup (2), and clamp washer (3).

Mounting of cutterblade with the hex wrench still in place

–Mount the cutter blade onto the shaft so that the guide of the receiver washer

(4) ﬁts in the arbor hole in the cutter blade. Install the clamp washer (3), cup (2), and secure the cutter blade with the nut (1).

[Tightening torque: 13 - 23 N-m]

NOTE: Always wear gloves when handling the cutter blade.

NOTE: The cutter blade-fastening nut (with spring washer) is a consumable part. If there appears any wear or deformation on the spring washer, replace the nut.

Mounting of nylon cutting head

–The clamp washer (3), cup (2), and nut (1) are not necessary for mounting the nylon cutting head. The nylon cutting head should go on top of the receiver washer (4).

–Insert the hex wrench through the hole in the gear case and rotate the receiver washer (4) until it is locked with the hex wrench.

–Then screw the nylon cutting head onto the shaft by turning it counter- clockwise.

–Remove the hex wrench.

Hex wrench

(4)

(3)

(2)

(1)

Hex wrench

Loosen Tighten

Hex wrench

Rotation

12

Image 12

Contents EM2650UH EM2650LH ImportanteSymbols Table of ContentsSafety Instructions General InstructionsIntended use of the machine Personal protective equipmentResting Transport Refueling Maintenance Tool replacement RefuelingMaintenance instructions Method of operationCutting Tools KickbackWhen asking for help, please give the following information Never straighten or weld damaged cutting toolsFirst Aid Technical Data EM2650UH, EM2650LH Model EM2650UH EM2650LHDesignation of Parts EM2650UHMounting of Handle For machines with bike handle modelsFor machines with loop handle Use of metal blade EM2650UH, optional accessory for EM2650LH Use of nylon cutting head EM2650UH, EM2650LHMounting of Protector For EM2650UHFor EM2650LH Mounting of Cutter Blade or Nylon Cutting Head Mounting of cutterblade with the hex wrench still in placeMounting of nylon cutting head Point 1 in Replacement of oil Oil cap Oil volumeBefore Start of Operation Inspection and reﬁll of engine oilRefueling Handling of fuelStorage period of fuel FuelPoints in Operation and HOW to Stop Correct Handling of MachineStarting At times, such as winter, when starting the engine Startup after warm-up operationAdjustment of LOW-SPEED Rotation Idling Resharpening the Cutting ToolStopping Checkup of LOW-SPEED RotationReplacing the nylon cord Daily checkup and maintenance Replacement of Engine OILServicing Instructions Cleaning of AIR Cleaner Points in Handling Air Cleaner ElementPoints on OIL Cleaning of Fuel Filter Replacement of Fuel PipeCleaning of Parts Replacement of Gaskets and PackingsFault location Fault System Observation CauseStorage Operating time Before Daily 50h ShutdownOperation 30h 200hTroubleshooting State of abnormality Probable cause malfunction RemedyStarts. Once engine starts, cutter blade BladeEmission Compliance Period MANUFACTURER’S Warranty Coverage Procedure Interval Emission Component Defect Warranty Period Parts CoveredObtaining Warranty Service What is not CoveredOWNER’S Warranty Responsibilities HOW to Make a Claim Pictogrammes Table des matièresConsignes DE Sécurité Consignes généralesUtilisation normale de la machine Équipement de protection personnelPause Transport Remplissage Entretien Remplacement d’outil RemplissageMode de fonctionnement Outils de coupeMouvement de recul Prévention des mouvements de reculPremiers soins Données Techniques EM2650UH, EM2650LH Modèle EM2650UH EM2650LHDésignation DES Pièces Désignation DES PiècesMontage DE LA Poignée Pour les machines avec guidonPour les machines avec poignée arceau Utilisation d’une tête à ﬁls nylon EM2650UH, EM2650LH Poignée SangleMontage DU Protecteur Pour le EM2650UHPour le EM2650LH Montage DE LA Lame DE Coupe OU DE LA Tête À Fils Nylon MakitaMontage de la tête à ﬁls nylon Avant Utilisation Inspection et remplissage de l’huile moteurQuantité d’huile Environ 0,08 l Remplissage Manipulation de l’essenceEntreposage de l’essence CarburantManipulation Correcte DE LA Machine Fixation de la sangle d’épauleDétachement DémarrageDémarrage après le réchauffage Pendant les périodes, telles que l’hiver, oùRéaffûtage DE L’OUTIL DE Coupe ArrêtRéglage DE LA Rotation À Faible Vitesse Ralenti Vérification DE LA Rotation À Faible VitesseRemplacement du ﬁl nylon Remplacement DE L’HUILE Moteur Huile recommandéeInstructions D’ENTRETIEN Vériﬁcation et entretien quotidiensRemarques Concernant L’HUILE Nettoyage DU Filtre À AIRRemplacement DU Tuyau D’ALIMENTATION EN Essence Remplacement DES Joints ET GarnituresVérification DE LA Bougie D’ALLUMAGE Lubrification DU Carter D’ENGRENAGEEmplacement des défaillances EntreposageDéfaillance Système Observation Cause Quotidien Fonctionnement Arrêt30 h 50 h 200 h PauseAnomalie Cause probable dysfonctionnement Solution DépannageFois le moteur démarré, la rotation de la Lame de coupe commence. Faites trèsSímbolos ÍndicePáginaInstrucciones DE Seguridad Instrucciones generalesUso intencionado de la herramienta Equipo protector personalResuministro de combustible Método de operación Piezas cortadorasRetrocesos bruscos Prevención de retrocesos bruscosPrimeros auxilios Especificaciones Técnicas EM2650UH, EM2650LH Modelo EM2650UH EM2650LHIdentificación DE LAS Piezas Identificación DE LAS PiezasColocación DEL Mango Para modelos equipados con mango tipo bicicletaPara modelos equipados con mango tipo redondo Uso de la cabeza cortadora de nailon EM2650UH, EM2650LH Colocación DEL Protector Para EM2650UHPara EM2650LH Colocación DEL Disco Cortador O Cabeza Cortadora DE Nailon Colocación de la cabeza cortadora de nailonVolumen de aceite Aprox ,08L Antes DE Iniciar LA OperaciónInspeccione y resuministre el aceite del motor Punto 1 en el reemplazo del aceite Tapa del aceiteReabastecimiento DE Combustible Manejo del combustiblePeriodo de almacenamiento del combustible CombustibleManejo Correcto DEL Equipo Puntos EN LA Operación Y Cómo Detener LA OperaciónArranque DEL Motor Arranque tras la operación de calentamiento En ciertas ocasiones, como en el invierno, cuandoReafilado DE LA Pieza Cortadora Paro DE LA OperaciónAjuste DE LA Rotación DE Baja Velocidad Estado Pasivo Revisión DE LA Rotación DE Baja VelocidadReemplazo del cordón de nailon Instrucciones DE Servicio Revisión y mantenimiento diariosReemplazo DEL Aceite DEL Motor Puntos Sobre EL Aceite Limpieza DEL Filtro DE AirePuntos en el manejo del elemento del ﬁltro de aire Engrasado DE LA Caja DE Cambios Revisión DE LA Bujía DE EncendidoInspección DE PERNOS, Tuercas Y Tornillos Limpieza DE LAS PiezasAlmacenamiento AtenciónAtención tras el almacenamiento de largo plazo Determinación de fallasAntes Tras la Diario AcciónOperación 30h 50h 200hResolución DE Problemas Estado de anomalía Causa probable falla SoluciónCortador Periodo DE Conformidad Sobre Emisiones Cobertura DE LA Garantía DEL Fabricante Procedimiento IntervaloPeriodo DE Garantía POR Defectos DE Componentes DE Emisiones Piezas CubiertasObtención DE Servicio DE Garantía LO QUE no Está CubiertoResponsabilidades DEL Propietario Para LA Garantía Cómo Preparar UNA Reclamación Page Advertencia