Craftsman 316.29271 STARTING/STOPPING Instructions, Starting Instructions, Stopping Instructions

Page 10

STARTING/STOPPING INSTRUCTIONS

WARNING: Operate this unit only in a well- ventilated

outdoor area. Carbon monoxide exhaust fumes can be lethal in a confined area.

WARNING: Avoid accidental starting. Make sure

you are in the starting position when pulling the starter rope (Fig. 12). To avoid serious injury, the operator and unit must be in a stable position while starting.

STARTING INSTRUCTIONS

1.Check the oil level in the crankcase. Refer to Checking the Oil Level.

2.Fill the fuel tank with fresh, clean unleaded gasoline. Refer to Fueling the Unit.

3.Put the On/Off Stop Control in the ON [I] position (Fig. 10).

4.Place the choke lever in Position 1 (Fig. 11).

5.Fully press and release the primer bulb 10 times, slowly. Some amount of fuel should be visible in the primer bulb and fuel lines (Fig. 11). If you can’t see fuel in the bulb, press and release the bulb as many times as it takes before you can see fuel in it.

6.Hold the throttle and handlebar with one hand and grab the starter rope with your other hand. Use your foot to hold down the cultivator (Fig. 12).

NOTE: Tilt the unit back slightly to bring the tines off the ground when starting.

7.While squeezing the throttle control, pull the starter rope with a smooth and steady pull. Repeat this 5 times.

NOTE: The unit uses the Incredi-Pull™starting system , which significantly reduces the effort required to start the engine. You must pull the starter rope out far enough to hear the engine attempt to start. There is no need to pull the rope briskly-- there is no harsh resistance when pulling. Be aware that this starting method is vastly different from (and much easier than) what you may be used to.

8.Move the choke lever to Position 2.

9.While squeezing the throttle control, pull the starter rope in the same manner as explained in Step 7. Pull 1 to 3 times to start the engine.

10.Keep the throttle squeezed and allow the engine to warm up for 15 to 30 seconds.

11.Place the choke lever in Position 3. Release the throttle control to the idle position and begin operation.

IF... The engine does not start, repeat Steps 4 - 11.

IF... The engine fails to start after a few attempts, place

the choke lever in Position 3 and squeeze the throttle control. Pull the starter rope 3 to 8 times. The engine should start. If not, continue pulling starter rope until the engine starts.

IF WARM... If the engine is already warm, make sure the On/Off Stop control is in the ON position and start the unit with the choke lever in Position 2. After the unit starts, move the choke lever to Position 3.

ON (I)

OFF (O)

Throttle

Control

Fig. 10

Choke Lever

Position 3

Position 2

Position 1

Primer Bulb

Fig. 11

Cultivator

Equipped With

Incredi-Pull

Starting

Fig. 12

STOPPING INSTRUCTIONS

1.Release your hand from the throttle control. Allow the engine to cool down by idling.

2.Put the On/Off Stop Control in the OFF (O) position.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Cultivator / Edger Introduction WarrantyTable of Contents California Proposition 65 WarningRules for Safe Operation Important Safety InstructionsSafety Warnings for GAS Units Before OperatingSave These Instructions Other Safety WarningsWhile Operating Symbol Meaning Safety and International SymbolsChoke Control Know Your Unit Know Your CultivatorPositioning the Handlebars Assembly InstructionsAdjusting Tine Depth Attaching the Edger Wheel and BladeRecommended OIL Type OIL and Fuel InformationAdding OIL to Crankcase Initial USE Recommended Fuel Type Fueling the UnitStarting Instructions STARTING/STOPPING InstructionsStopping Instructions Transporting the Unit Operating InstructionsOperating Tips Never pick-up or carry the unit while the engine is runningTine Removal and Replacement Maintenance and Repair InstructionsFrequency Maintenance Required Refer to Maintenance ScheduleChanging the OIL Checking the OIL LevelHandling the unit AIR Filter Maintenance Carburetor AdjustmentReplacing the Spark Plug Spark Arrestor MaintenanceElectrodes. Grit in the engine could damage the cylinder Long Term Storage Cleaning the UnitStorage TransportingTroubleshooting Rocker ARM Clearance Remove the rocker arm cover and gasketIntake Exhaust Engine SpecificationsCultivator Page Owner’s Warranty Responsibilities Your Warranty Rights and ObligationsManufacturer’s Warranty Coverage Cultivadora / Bordeadora Indice DE Contenidos IntroduccionGarantia Proposición 65 DE CaliforniaNormas Para UNA Operacion Segura Importante Informacion DE SeguridadAdvertencia Laes muygasolina Lea Todas las Instrucciones Antest DE LA OperaciónDurante la Operación Conserve Estas InstruccionesOtras Advertencias de Seguridad Advertencia Advertencia NoAdvertencia Los Simbolos DE Seguridad DE IntercacionalesConozca SU Unidad Conozca SU UnidadAplicacion Ajuste DE LA Profundidad Instrucciones DE EnsambleColocación DEL Manubrio Conexión DE LA Rueda Y DE LA Cuchilla DE LA BordeadoraTipo DE Aceite Recomendado Advertencia EL LlenarInformacion DEL Aceite Y DEL Combustible Carga E Aceite EN EL Carter DEL Cigüeñal USO InicialAdvertencia Cargue el Advertencia Lagasolina esAdvertencia Saque la Tipo DE Combustible RecomendadoInstrucciones DE Arranque Advertencia Evite losInstrucciones DE Arranque Y Apagado Instrucciones DE ApagadoAdvertencia evitarPara Advertencia formaAdvertencia graves Advertencia Para evitarFrecuencia Mantenimiento Requerido Consulte Instrucciones DE Mantenimiento Y ReparacionPrograma DE Mantenimiento Remoción Y Reposición DE LAS PuasInspección DEL Nivel DE Aceite Precaucion Para evitarPrecaucion Use guantes Cambio DEL AceiteLimpieza del filtro de aire Mantenimiento DEL Filtro DE AireAjuste DEL Carburador Inspección del CombustibleMantenimiento DEL Amortiguador DE Chispas Precaucion No limpieCambio de la Bujía de Encendido Transporte AlmacenamientoLimpieza de la Unidad EL Motor no Funciona EN Minima Resolucion DE ProblemasEL Motor no Arranca EL Motor no AceleraHuelgo DEL Brazo Oscilante Entrada Motor EspecificacionesEJE Impulsor Y Cultivador Parts List Engine Parts Model Sears Cultivator 4-CYCLE GAS Cultivator 753-04059 Clevis Pin Responsabilidades del Propietario para la Garantiá Cobertura de la Garantía del FabricanteRepair Protection Agreements Get it fixed, at your home or ours

316.29271 specifications

The Craftsman 316.29271 is a versatile and robust power tool ideal for both professional tradespeople and DIY enthusiasts. This model represents the pinnacle of functionality and convenience in the world of electric tools, making it a must-have in any workshop.

One of the standout features of the Craftsman 316.29271 is its powerful motor. Equipped with a high-performance engine, it delivers exceptional torque and speed, allowing users to tackle a wide variety of tasks with ease. Whether you are drilling, driving screws, or working on intricate projects, this tool ensures optimal performance every time.

Another key feature of the Craftsman 316.29271 is its ergonomic design. The tool is built with user comfort in mind, featuring a soft-grip handle that minimizes vibration and reduces hand fatigue during extended use. This thoughtful design enhances overall control and precision, making it easier to navigate tight spaces and intricate tasks.

The Craftsman 316.29271 also incorporates advanced technologies that set it apart from other tools in its category. Its variable speed settings allow users to adjust the speed according to the specific task at hand, providing maximum versatility. Additionally, the tool's built-in LED work light illuminates dark work areas, ensuring visibility and accuracy even in low-light conditions.

Durability is another hallmark of the Craftsman 316.29271. Constructed with high-quality materials, this tool is designed to withstand the rigors of frequent use. Its rugged exterior not only protects the internal components but also contributes to a long lifespan, making it a wise investment for both casual and serious users.

The Craftsman 316.29271 is compatible with a wide range of accessories, which enhances its versatility even further. From drilling bits to screwdriver attachments, users can easily switch out components to suit their specific project needs. This adaptability makes it an excellent choice for tackling various applications, from minor repairs to major renovations.

In summary, the Craftsman 316.29271 combines power, comfort, and durability in a sleek, innovative design. With its impressive motor, ergonomic features, and advanced technologies, this tool is well-equipped to handle a multitude of tasks with ease and efficiency. Whether you're a seasoned professional or a home improvement novice, the Craftsman 316.29271 is a reliable companion for all your crafting and construction needs.
Top Page Image Contents