Craftsman 316.29271 manual Rocker ARM Clearance, Remove the rocker arm cover and gasket

Page 18

TROUBLESHOOTING

ROCKER ARM CLEARANCE

The rocker arm clearance may need adjustment if your unit suffers a loss of performance power or has trouble starting. Adjusting the rocker arm clearance requires disassembly of the engine. If you feel unsure or unqualified to perform this, take the unit to a Sears or other qualified service dealer.

NOTE: Inspect the valve to rocker arm clearance with a feeler gauge after the first 10 hours of operation and then every 25 hours of operation thereafter.

•The engine must be cold when checking or adjusting the valve clearance.

•This task should be performed inside, in a clean, dust free area.

To adjust the rocker arm clearance:

1.Remove the two (2) screws on top of the engine cover with a Flat-head or T-25 Torx screwdriver (Fig. 25).

Top View Of The Engine

Screw

Fig. 26

3.Disconnect the spark plug wire.

4.Clean dirt from around the spark plug. Remove the spark plug from the cylinder head by turning it counterclockwise with a 5/8” socket.

5.Remove the engine cover.

Engine Cover

Remove Screws

Muffler

NOTE: To ease engine cover removal, pull the starter rope out a little to give some slack.

6.Clean dirt from around the rocker arm cover. Remove the screw holding the rocker arm cover with a large flat blade screwdriver or Torx T-25 bit

(Fig. 27). Remove the rocker arm cover and gasket.

Rocker Arm Cover

Gasket

Spark Plug Hole

Fig. 25

2. Remove the screw behind the engine cover (Fig. 26).

Fig. 27

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Cultivator / Edger Introduction WarrantyTable of Contents California Proposition 65 WarningRules for Safe Operation Important Safety InstructionsSafety Warnings for GAS Units Before OperatingOther Safety Warnings Save These InstructionsWhile Operating Safety and International Symbols Symbol MeaningChoke Control Know Your Unit Know Your CultivatorPositioning the Handlebars Assembly InstructionsAdjusting Tine Depth Attaching the Edger Wheel and BladeOIL and Fuel Information Recommended OIL TypeAdding OIL to Crankcase Initial USE Recommended Fuel Type Fueling the UnitSTARTING/STOPPING Instructions Starting InstructionsStopping Instructions Transporting the Unit Operating InstructionsOperating Tips Never pick-up or carry the unit while the engine is runningTine Removal and Replacement Maintenance and Repair InstructionsFrequency Maintenance Required Refer to Maintenance ScheduleChecking the OIL Level Changing the OILHandling the unit AIR Filter Maintenance Carburetor AdjustmentSpark Arrestor Maintenance Replacing the Spark PlugElectrodes. Grit in the engine could damage the cylinder Long Term Storage Cleaning the UnitStorage TransportingTroubleshooting Rocker ARM Clearance Remove the rocker arm cover and gasketIntake Exhaust Specifications EngineCultivator Page Your Warranty Rights and Obligations Owner’s Warranty ResponsibilitiesManufacturer’s Warranty Coverage Cultivadora / Bordeadora Indice DE Contenidos IntroduccionGarantia Proposición 65 DE CaliforniaNormas Para UNA Operacion Segura Importante Informacion DE SeguridadAdvertencia Laes muygasolina Lea Todas las Instrucciones Antest DE LA OperaciónConserve Estas Instrucciones Durante la OperaciónOtras Advertencias de Seguridad Advertencia Advertencia NoAdvertencia Los Simbolos DE Seguridad DE IntercacionalesConozca SU Unidad Conozca SU UnidadAplicacion Ajuste DE LA Profundidad Instrucciones DE EnsambleColocación DEL Manubrio Conexión DE LA Rueda Y DE LA Cuchilla DE LA BordeadoraTipo DE Aceite Recomendado Advertencia EL LlenarInformacion DEL Aceite Y DEL Combustible Carga E Aceite EN EL Carter DEL Cigüeñal USO InicialAdvertencia Cargue el Advertencia Lagasolina esAdvertencia Saque la Tipo DE Combustible RecomendadoInstrucciones DE Arranque Advertencia Evite losInstrucciones DE Arranque Y Apagado Instrucciones DE ApagadoAdvertencia evitarPara Advertencia formaAdvertencia graves Advertencia Para evitarFrecuencia Mantenimiento Requerido Consulte Instrucciones DE Mantenimiento Y ReparacionPrograma DE Mantenimiento Remoción Y Reposición DE LAS PuasInspección DEL Nivel DE Aceite Precaucion Para evitarPrecaucion Use guantes Cambio DEL AceiteLimpieza del filtro de aire Mantenimiento DEL Filtro DE AireAjuste DEL Carburador Inspección del CombustiblePrecaucion No limpie Mantenimiento DEL Amortiguador DE ChispasCambio de la Bujía de Encendido Almacenamiento TransporteLimpieza de la Unidad EL Motor no Funciona EN Minima Resolucion DE ProblemasEL Motor no Arranca EL Motor no AceleraHuelgo DEL Brazo Oscilante Entrada Especificaciones MotorEJE Impulsor Y Cultivador Parts List Engine Parts Model Sears Cultivator 4-CYCLE GAS Cultivator 753-04059 Clevis Pin Responsabilidades del Propietario para la Garantiá Cobertura de la Garantía del FabricanteRepair Protection Agreements Get it fixed, at your home or ours

316.29271 specifications

The Craftsman 316.29271 is a versatile and robust power tool ideal for both professional tradespeople and DIY enthusiasts. This model represents the pinnacle of functionality and convenience in the world of electric tools, making it a must-have in any workshop.

One of the standout features of the Craftsman 316.29271 is its powerful motor. Equipped with a high-performance engine, it delivers exceptional torque and speed, allowing users to tackle a wide variety of tasks with ease. Whether you are drilling, driving screws, or working on intricate projects, this tool ensures optimal performance every time.

Another key feature of the Craftsman 316.29271 is its ergonomic design. The tool is built with user comfort in mind, featuring a soft-grip handle that minimizes vibration and reduces hand fatigue during extended use. This thoughtful design enhances overall control and precision, making it easier to navigate tight spaces and intricate tasks.

The Craftsman 316.29271 also incorporates advanced technologies that set it apart from other tools in its category. Its variable speed settings allow users to adjust the speed according to the specific task at hand, providing maximum versatility. Additionally, the tool's built-in LED work light illuminates dark work areas, ensuring visibility and accuracy even in low-light conditions.

Durability is another hallmark of the Craftsman 316.29271. Constructed with high-quality materials, this tool is designed to withstand the rigors of frequent use. Its rugged exterior not only protects the internal components but also contributes to a long lifespan, making it a wise investment for both casual and serious users.

The Craftsman 316.29271 is compatible with a wide range of accessories, which enhances its versatility even further. From drilling bits to screwdriver attachments, users can easily switch out components to suit their specific project needs. This adaptability makes it an excellent choice for tackling various applications, from minor repairs to major renovations.

In summary, the Craftsman 316.29271 combines power, comfort, and durability in a sleek, innovative design. With its impressive motor, ergonomic features, and advanced technologies, this tool is well-equipped to handle a multitude of tasks with ease and efficiency. Whether you're a seasoned professional or a home improvement novice, the Craftsman 316.29271 is a reliable companion for all your crafting and construction needs.
Top Page Image Contents