Craftsman 316.29271 manual Assembly Instructions, Positioning the Handlebars, Adjusting Tine Depth

Page 7

ASSEMBLY INSTRUCTIONS

NOTE: Before setting up your cultivator / edger, disconnect the spark plug wire from the spark plug.

POSITIONING THE HANDLEBARS

1.Loosen the two knobs on the inside of the handlebars (Fig. 1).

2.With the unit upright, swing the handlebars up into the operating position (Fig. 1).

NOTE: Take care not to pinch the throttle cable or switch wires when positioning the handlebar.

3. Tighten the knobs to secure the handlebars in place.

NOTE: Do not over-tighten the knobs.

4. Reconnect the spark plug wire to the spark plug.

Fig. 1

Handlebars

Bolt

Handlebar

Knob

Washer

Hole

 

 

Fig. 2

ADJUSTING TINE DEPTH

To adjust the wheel support bracket proceed as follows:

1.Stop engine and disconnect spark plug to avoid accidental starting.

2.Remove cotter pin from the clevis pin and slide clevis pin out of tailpiece bracket (Fig. 3).

3.Slide the wheel support bracket up or down in the tailpiece, aligning the holes to the desire height.

4.Place the clevis pin through the hole and secure with cotter pin.

Clevis Pin

Cotter Pin

Wheel

Support

Bracket

Tailpiece Bracket

Fig. 3

ATTACHING THE EDGER WHEEL AND BLADE

To convert the cultivator to an edger proceed as follows:

1.Push the On/Off switch to Off (O) position to stop engine and tines and disconnect spark plug to avoid accidental starting.

NOTE: It may be necessary to lay the cultivator / edger back in a horizontal position on a flat level surface with the upper handle touching the ground.

2.Remove the click pin from each end of the tine shaft and slide the tines off the shaft.

3.Slide the edger wheel, with the hub facing inward, onto the right side of the tine shaft and secure with the click pin in the inside hole (Fig. 4).

4.Slide the edger blade with the hub facing out onto the left side of tine shaft and secure with the click pin in the inside hole (Fig. 4).

5.The edger guide line indicates where cutting will occur. Guide the unit along a flowerbed, sidewalk, or driveway so the edger guide line is above the desired line of cut.

Edger Guide

Line

Hub

Edger Wheel

Click Pin

Tine Shaft

Edger Blade

Fig. 4

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Cultivator / Edger California Proposition 65 Warning WarrantyTable of Contents IntroductionBefore Operating Important Safety InstructionsSafety Warnings for GAS Units Rules for Safe OperationSave These Instructions Other Safety WarningsWhile Operating Symbol Meaning Safety and International SymbolsChoke Control Know Your Cultivator Know Your UnitAttaching the Edger Wheel and Blade Assembly InstructionsAdjusting Tine Depth Positioning the HandlebarsRecommended OIL Type OIL and Fuel InformationAdding OIL to Crankcase Initial USE Fueling the Unit Recommended Fuel TypeStarting Instructions STARTING/STOPPING InstructionsStopping Instructions Never pick-up or carry the unit while the engine is running Operating InstructionsOperating Tips Transporting the UnitMaintenance Schedule Maintenance and Repair InstructionsFrequency Maintenance Required Refer to Tine Removal and ReplacementChanging the OIL Checking the OIL LevelHandling the unit Carburetor Adjustment AIR Filter MaintenanceReplacing the Spark Plug Spark Arrestor MaintenanceElectrodes. Grit in the engine could damage the cylinder Transporting Cleaning the UnitStorage Long Term StorageTroubleshooting Remove the rocker arm cover and gasket Rocker ARM ClearanceIntake Exhaust Engine SpecificationsCultivator Page Owner’s Warranty Responsibilities Your Warranty Rights and ObligationsManufacturer’s Warranty Coverage Cultivadora / Bordeadora Proposición 65 DE California IntroduccionGarantia Indice DE ContenidosLea Todas las Instrucciones Antest DE LA Operación Importante Informacion DE SeguridadAdvertencia Laes muygasolina Normas Para UNA Operacion SeguraDurante la Operación Conserve Estas InstruccionesOtras Advertencias de Seguridad Simbolos DE Seguridad DE Intercacionales Advertencia NoAdvertencia Los AdvertenciaConozca SU Unidad Conozca SU UnidadAplicacion Conexión DE LA Rueda Y DE LA Cuchilla DE LA Bordeadora Instrucciones DE EnsambleColocación DEL Manubrio Ajuste DE LA ProfundidadCarga E Aceite EN EL Carter DEL Cigüeñal USO Inicial Advertencia EL LlenarInformacion DEL Aceite Y DEL Combustible Tipo DE Aceite RecomendadoTipo DE Combustible Recomendado Advertencia Lagasolina esAdvertencia Saque la Advertencia Cargue elInstrucciones DE Apagado Advertencia Evite losInstrucciones DE Arranque Y Apagado Instrucciones DE ArranqueAdvertencia Para evitar Advertencia formaAdvertencia graves Advertencia evitarParaRemoción Y Reposición DE LAS Puas Instrucciones DE Mantenimiento Y ReparacionPrograma DE Mantenimiento Frecuencia Mantenimiento Requerido ConsulteCambio DEL Aceite Precaucion Para evitarPrecaucion Use guantes Inspección DEL Nivel DE AceiteInspección del Combustible Mantenimiento DEL Filtro DE AireAjuste DEL Carburador Limpieza del filtro de aireMantenimiento DEL Amortiguador DE Chispas Precaucion No limpieCambio de la Bujía de Encendido Transporte AlmacenamientoLimpieza de la Unidad EL Motor no Acelera Resolucion DE ProblemasEL Motor no Arranca EL Motor no Funciona EN MinimaHuelgo DEL Brazo Oscilante Entrada Motor EspecificacionesEJE Impulsor Y Cultivador Parts List Engine Parts Model Sears Cultivator 4-CYCLE GAS Cultivator 753-04059 Clevis Pin Cobertura de la Garantía del Fabricante Responsabilidades del Propietario para la GarantiáRepair Protection Agreements Get it fixed, at your home or ours

316.29271 specifications

The Craftsman 316.29271 is a versatile and robust power tool ideal for both professional tradespeople and DIY enthusiasts. This model represents the pinnacle of functionality and convenience in the world of electric tools, making it a must-have in any workshop.

One of the standout features of the Craftsman 316.29271 is its powerful motor. Equipped with a high-performance engine, it delivers exceptional torque and speed, allowing users to tackle a wide variety of tasks with ease. Whether you are drilling, driving screws, or working on intricate projects, this tool ensures optimal performance every time.

Another key feature of the Craftsman 316.29271 is its ergonomic design. The tool is built with user comfort in mind, featuring a soft-grip handle that minimizes vibration and reduces hand fatigue during extended use. This thoughtful design enhances overall control and precision, making it easier to navigate tight spaces and intricate tasks.

The Craftsman 316.29271 also incorporates advanced technologies that set it apart from other tools in its category. Its variable speed settings allow users to adjust the speed according to the specific task at hand, providing maximum versatility. Additionally, the tool's built-in LED work light illuminates dark work areas, ensuring visibility and accuracy even in low-light conditions.

Durability is another hallmark of the Craftsman 316.29271. Constructed with high-quality materials, this tool is designed to withstand the rigors of frequent use. Its rugged exterior not only protects the internal components but also contributes to a long lifespan, making it a wise investment for both casual and serious users.

The Craftsman 316.29271 is compatible with a wide range of accessories, which enhances its versatility even further. From drilling bits to screwdriver attachments, users can easily switch out components to suit their specific project needs. This adaptability makes it an excellent choice for tackling various applications, from minor repairs to major renovations.

In summary, the Craftsman 316.29271 combines power, comfort, and durability in a sleek, innovative design. With its impressive motor, ergonomic features, and advanced technologies, this tool is well-equipped to handle a multitude of tasks with ease and efficiency. Whether you're a seasoned professional or a home improvement novice, the Craftsman 316.29271 is a reliable companion for all your crafting and construction needs.
Top Page Image Contents