Craftsman 316.29271 manual Troubleshooting

Page 17

TROUBLESHOOTING

ENGINE WILL NOT START

C A U S E

Empty fuel tank

Primer bulb wasn't pressed enough Engine is flooded

Old fuel

Fouled spark plug

Plugged spark arrestor

On/Off Control is in the OFF (O) position

ENGINE WILL NOT IDLE

C A U S E

Air filter is plugged

Old fuel

Improper carburetor adjustment

A C T I O N

Fill fuel tank with new fuel

Press primer bulb fully and slowly 10 times

Pull starter rope repeatedly with throttle control fully engaged and with the choke lever in Position 3

Drain gas tank and add fresh fuel

Replace or clean the spark plug

Clean or replace spark arrestor

Move switch to ON (I)

A C T I O N

Replace or clean the air filter

Drain gas tank and add fresh fuel

Adjust according to the Carburetor Adjustments section

ENGINE WILL NOT ACCELERATE

C A U S E

Old fuel

Improper carburetor adjustment

Dirty air filter

Plugged spark arrestor

A C T I O N

Drain gas tank and add fresh fuel

Take unit to a Sears or other qualified service dealer for an adjustment

Clean or replace the air filter

Clean or replace spark arrestor

ENGINE LACKS POWER OR STALLS WHEN UNDER LOAD

C A U S E

Old fuel

Improper carburetor adjustment

Fouled spark plug

Plugged spark arrestor

Low power

Cultivator tines bound with dirt or grass

A C T I O N

Drain gas tank and add fresh fuel

Take unit to a Sears or other qualified service dealer for an adjustment

Replace or clean the spark plug

Clean or replace spark arrestor

Rocker arm clearance adjustment (see page 18)

Stop the unit, switch the On/Off Stop Control to STOP, clean and remove any debris binding the tines

SIGNS OF OIL AROUND OIL FILL PLUG/DIPSTICK

C A U S E

Oil fill plug/dipstick loose or missing o-ring

A C T I O N

Tighten oil fill plug/dipstick, replace o-ring

UNIT OCCASIONALLY HESITATES AT HIGH SPEEDS

C A U SE

Spark plug gap is too small/close

A C T I O N

Adjust gap to 0.025”

NOTE: For repairs beyond the minor adjustments listed above, contact your nearest Sears Parts & Repair center (1-800-4-MY-HOME®) or other qualified service dealer for an adjustment.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Cultivator / Edger Table of Contents WarrantyIntroduction California Proposition 65 WarningSafety Warnings for GAS Units Important Safety InstructionsRules for Safe Operation Before OperatingWhile Operating Other Safety WarningsSave These Instructions Choke Control Safety and International SymbolsSymbol Meaning Know Your Cultivator Know Your UnitAdjusting Tine Depth Assembly InstructionsPositioning the Handlebars Attaching the Edger Wheel and BladeAdding OIL to Crankcase Initial USE OIL and Fuel InformationRecommended OIL Type Fueling the Unit Recommended Fuel TypeStopping Instructions STARTING/STOPPING InstructionsStarting Instructions Operating Tips Operating InstructionsTransporting the Unit Never pick-up or carry the unit while the engine is runningFrequency Maintenance Required Refer to Maintenance and Repair InstructionsTine Removal and Replacement Maintenance ScheduleHandling the unit Checking the OIL LevelChanging the OIL Carburetor Adjustment AIR Filter MaintenanceElectrodes. Grit in the engine could damage the cylinder Spark Arrestor MaintenanceReplacing the Spark Plug Storage Cleaning the UnitLong Term Storage TransportingTroubleshooting Remove the rocker arm cover and gasket Rocker ARM ClearanceIntake Exhaust Cultivator SpecificationsEngine Page Manufacturer’s Warranty Coverage Your Warranty Rights and ObligationsOwner’s Warranty Responsibilities Cultivadora / Bordeadora Garantia IntroduccionIndice DE Contenidos Proposición 65 DE CaliforniaAdvertencia Laes muygasolina Importante Informacion DE SeguridadNormas Para UNA Operacion Segura Lea Todas las Instrucciones Antest DE LA OperaciónOtras Advertencias de Seguridad Conserve Estas InstruccionesDurante la Operación Advertencia Los Advertencia NoAdvertencia Simbolos DE Seguridad DE IntercacionalesAplicacion Conozca SU UnidadConozca SU Unidad Colocación DEL Manubrio Instrucciones DE EnsambleAjuste DE LA Profundidad Conexión DE LA Rueda Y DE LA Cuchilla DE LA BordeadoraInformacion DEL Aceite Y DEL Combustible Advertencia EL LlenarTipo DE Aceite Recomendado Carga E Aceite EN EL Carter DEL Cigüeñal USO InicialAdvertencia Saque la Advertencia Lagasolina esAdvertencia Cargue el Tipo DE Combustible RecomendadoInstrucciones DE Arranque Y Apagado Advertencia Evite losInstrucciones DE Arranque Instrucciones DE ApagadoAdvertencia graves Advertencia formaAdvertencia evitarPara Advertencia Para evitarPrograma DE Mantenimiento Instrucciones DE Mantenimiento Y ReparacionFrecuencia Mantenimiento Requerido Consulte Remoción Y Reposición DE LAS PuasPrecaucion Use guantes Precaucion Para evitarInspección DEL Nivel DE Aceite Cambio DEL AceiteAjuste DEL Carburador Mantenimiento DEL Filtro DE AireLimpieza del filtro de aire Inspección del CombustibleCambio de la Bujía de Encendido Precaucion No limpieMantenimiento DEL Amortiguador DE Chispas Limpieza de la Unidad AlmacenamientoTransporte EL Motor no Arranca Resolucion DE ProblemasEL Motor no Funciona EN Minima EL Motor no AceleraHuelgo DEL Brazo Oscilante Entrada EJE Impulsor Y Cultivador EspecificacionesMotor Parts List Engine Parts Model Sears Cultivator 4-CYCLE GAS Cultivator 753-04059 Clevis Pin Cobertura de la Garantía del Fabricante Responsabilidades del Propietario para la GarantiáRepair Protection Agreements Get it fixed, at your home or ours

316.29271 specifications

The Craftsman 316.29271 is a versatile and robust power tool ideal for both professional tradespeople and DIY enthusiasts. This model represents the pinnacle of functionality and convenience in the world of electric tools, making it a must-have in any workshop.

One of the standout features of the Craftsman 316.29271 is its powerful motor. Equipped with a high-performance engine, it delivers exceptional torque and speed, allowing users to tackle a wide variety of tasks with ease. Whether you are drilling, driving screws, or working on intricate projects, this tool ensures optimal performance every time.

Another key feature of the Craftsman 316.29271 is its ergonomic design. The tool is built with user comfort in mind, featuring a soft-grip handle that minimizes vibration and reduces hand fatigue during extended use. This thoughtful design enhances overall control and precision, making it easier to navigate tight spaces and intricate tasks.

The Craftsman 316.29271 also incorporates advanced technologies that set it apart from other tools in its category. Its variable speed settings allow users to adjust the speed according to the specific task at hand, providing maximum versatility. Additionally, the tool's built-in LED work light illuminates dark work areas, ensuring visibility and accuracy even in low-light conditions.

Durability is another hallmark of the Craftsman 316.29271. Constructed with high-quality materials, this tool is designed to withstand the rigors of frequent use. Its rugged exterior not only protects the internal components but also contributes to a long lifespan, making it a wise investment for both casual and serious users.

The Craftsman 316.29271 is compatible with a wide range of accessories, which enhances its versatility even further. From drilling bits to screwdriver attachments, users can easily switch out components to suit their specific project needs. This adaptability makes it an excellent choice for tackling various applications, from minor repairs to major renovations.

In summary, the Craftsman 316.29271 combines power, comfort, and durability in a sleek, innovative design. With its impressive motor, ergonomic features, and advanced technologies, this tool is well-equipped to handle a multitude of tasks with ease and efficiency. Whether you're a seasoned professional or a home improvement novice, the Craftsman 316.29271 is a reliable companion for all your crafting and construction needs.
Top Page Image Contents