Black & Decker LPP120B Charging Procedure, Each use, Leaving the battery in the charger

Page 8

WARNING: Burn hazard. Battery liquid may be flammable if exposed to spark or flame.

Charge the battery packs only in Black & Decker chargers.

DO NOT splash or immerse in water or other liquids. This may cause premature cell failure.

Do not store or use the tool and battery pack in locations where the temperature may reach or exceed 105°F (40˚C) (such as outside sheds or metal buildings in summer).

WARNING: Never attempt to open the battery pack for any reason. If battery pack case is cracked or damaged, do not insert into charger. Do not crush, drop or damage battery pack. Do not use a battery pack or charger that has received a sharp blow, been dropped, run over or damaged in any way (i.e., pierced with a nail, hit with a hammer, stepped on). Damaged battery packs should be returned to service center for recycling.

WARNING: Fire hazard. Do not store or carry battery so that metal objects can contact exposed battery terminals. For example, do not place battery in aprons, pockets, tool boxes, product kit boxes, drawers, etc., with loose nails, screws, keys, etc.

Transporting batteries can possibly cause fires if the battery terminals inadvertently come in contact with conductive materials such as keys, coins, hand tools and the like. The US Department of Transportation Hazardous Material Regulations (HMR) actually prohibit transporting batteries in commerce or on airplanes (i.e., packed in suitcases and carry-on luggage) UNLESS they are properly protected from short circuits. So when transporting individual batteries, make sure that the battery terminals are protected and well insulated from materials that could contact them and cause a short circuit. NOTE: LI-ION batteries should not be put in checked baggage.

Storage Recommendations

1. The best storage place is one that is cool and dry away from direct sunlight and excess heat or cold.

2. Long storage will not harm the battery pack or charger.

Charging Procedure

The standard charger provided will charge a fully depeleted battery in

about 4 hours.

 

1. Plug the charger into an appropriate outlet before inserting the

battery pack.

1

2. Insert the battery pack into the

charger as shown in figure 1.

 

3. The green LED will flash

 

indicating that the battery is being

 

charged.

 

4. The completion of charge

 

is indicated by the green LED

 

remaining on continuously. The pack

 

is fully charged and may be used at

 

this time or left on the charger.

 

Recharge discharged batteries

 

as soon as possible after use or battery life may be greatly

diminished. It is recommended that the batteries be recharged after

each use.

 

Leaving the battery in the charger

The charger and battery pack can be left connected with the green LED glowing indefinitely. The charger will keep the battery pack fresh and fully charged.

Important Charging Notes

1. Longest life and best performance can be obtained if the battery pack is charged when the air temperature is between 60°F and 80°F (16°- 27°C). DO NOT charge the battery pack in an air temperature below +40°F (+4.5°C), or above +105°F (+40.5°C). This is important and will prevent serious damage to the battery pack.

2. The charger and battery pack may become warm to touch while charging. This is a normal condition, and does not indicate a problem. To facilitate the cooling of the battery pack after use, avoid placing the charger or battery pack in a warm environment such as in a metal shed, or an uninsulated trailer.

8

Image 8
Contents 20V MAX* LITHIUM pole SAW Table of Contents Important Safety RulesGeneral Safety Rules ServiceWhile Operating Pole Saw Do not operate Pole SawKickback Safety Features Specific Safety RulesComponents Important safety instructions For battery chargers Pole Saw Names and TermsImportant safety warnings For battery packs Read all InstructionsCharging Procedure Leaving the battery in the chargerEach use Important Charging NotesInstalling and Removing Saw Chain Adjusting Chain Tension Chain OilingAssembly Transporting Pole SawJoining Saw Head Module to Handle Module Until it stops and completely coversDisassembly Operating the Pole SawPruning With the Pole Saw Always WearDo not overreach. Make sure your footing is Use both hands to grip Pole Saw as shownAccessories Pole Saw Maintenance SectionTroubleshooting Saw chain sharpnessService Information Troubleshooting Con’tAccessories Yellow Pages Full Two-Year Home Use WarrantySee ‘Tools-Electric’ Pour enregistrer votre nouveau produit Lignes directrices en matière de sécurité définitions Table DES MatièresConsignes DE Securite Importantes Pendant l’utilisation de la scie à long mancheNe pas utiliser la scie à long manche RÈgles de sÉcuritÉ GÉnÉralitÉsEntretien Dispositif de protection contre les rebondsDispositifs de sécurité anti-rebonds Consignes de sÉcuritÉ particuliÈresComposantes Module de poignée Module central Module de tête de scieGlossaire terminologique de la scie à long manche Conserver ces mesures Directives de sÉcuritÉ importantes pour Les blocs-pilesNE Jamais tenter de relier deux chargeurs ensemble Le bloc-piles n’est pas complètement chargé à la sortie deRecommandations en matière de rangement Lire toutes les directivesProcédure de charge En cours de charge La fin de la charge est indiquéeChaque utilisation Pile laissée dans le chargeurInstallation et retrait de la chaîne coupante Insertion et retrait du bloc-piles de ’outilPrÉparation de la scie À long manche Pour son utilisation ’outil bRéglage de la tension de la chaîne Graissage de la chaîneAssemblage Orange comme illustré en FigureDe tête de scie Aligner la rainure du bord externe du Du module central B. Se reporter enDÉmontage Utilisation de la scie À long mancheProtéger les doigts du couloir Élagage Ébranchage avec la scie à long mancheNe jamais utiliser une échelle ou tout autre Accessoires Affûtage de la chaîne coupanteTension de la chaîne coupante Entretien de la scie À long mancheSolution possible Cause probable Solution possibleGuide de dÉpannage Problème Cause probableBlack & Decker Information sur les réparationsLe sceau Srprcmc Si tiene una consulta o algún inconveniente con su producto Para obtener respuestas instantáneas las 24 horas del díaÍndice Pautas DE SEGURIDAD/DEFINICIONESReglas importantes DE Seguridad Al operar la garrocha podadoraNo opere la garrocha podadora Reglas DE Seguridad GeneralesServicio Protector contra reboteCaracterísticas de seguridad contra rebote Normas Específicas DE SeguridadConserve Estas Instrucciones Amperios VatiosComponentes Nombres y terminología para la garrocha podadoraBatería Funda Empuñadura de espuma Botella de aceitePoda El proceso de cortar ramas en un árbol Esto reducirá el riesgo de dañar el enchufe y el cableLea todas las instrucciones Procedimiento de carga Advertencia Riesgo de incendio. NoCompletamente cargado y puede utilizarse en este momento o Dejarse en el cargadorNotas importantes sobre la carga Para instalar el paquete deAjuste de la tensión de la Cadena PreparaciÓn para el uso de su garrocha PodadoraInstalación y desmantelamiento de la cadena de la sierra Unión del módulo de la sierra con el módulo del mango Aceitado de la cadenaMontaje Desmantelamiento Separación del módulo de la sierraOperaciÓn de la garrocha Conexión de la bateríaConmutador Sistema de detención automático de la cadenaPoda con la garrocha podadora Para Apagar la herramienta, suelte el gatilloPara podar con la garrocha podadora Filo de la cadena de la sierraTensión de la cadena de la sierra No se sobreextienda. Verifique que esté bienDEteccion de problemas Problema Causa posible Posible soluciónAccesorios SecciÓn de mantenimiento de la garrocha PodadoraInformación de mantenimiento Solamente para Propósitos de México El sello RbrcGarantía completa de dos años para uso en El hogar AñOS DE Garantia Esta Garantia no Aplica CuandoPage Perfiles y Herramientas de Morelia Gpo. Comercial de Htas. y RefaccionesFerre Pat de Puebla, S.A. de C.V De Occidente, S.A. de C.V Enrique Robles
Related manuals
Manual 56 pages 54.3 Kb