Husqvarna PT26 D manual Transport, Environment protection

Page 14

Safety Instructions

•Reduce the risk of ﬁre by removing grass, leaves and other debris that may have fastened in the machine. Allow the machine to cool before putting it in storage.

•Do not turn over the engine by hand without preventing the engine from starting, which can be done in different ways:

a.Remove the glow plug, no compression the engine can therefore be easily turned over.

b.Loosen a pressure pipe connection on each jet pipe a 1/2 turn.

c.Secure the injection pump stop arm in position for zero supply.

Transport

IMPORTANT INFORMATION:

The parking brake is not sufﬁcient to lock the machine during transport. Ensure you secure the machine ﬁrmly to the transporting vehicle.

The machine is heavy and can cause serious crushing injuries. Be extra cautious when it is loaded on or unloaded from a vehicle or trailer.

•Use an approved trailer to transport the machine. Activate the parking brake and secure the machine using approved fasteners, such as straps, chains or ropes when transporting.

•Check and comply with laws and regulations when driving on public roads, a trafﬁc kit is available as an option. This can be retroﬁtted on PT 26D.

Environment protection

Take care of the environment, there are numerous environmental risks especially when performing maintenance on the machine. This particularly applies when dealing with engine oil, hydraulic oil, fuel, oil ﬁlters, hydraulic ﬁlters and fuel ﬁlters. You must be attentive to ensure spillage does not occur when you open a system that contains oil or fuel.

•Always wipe up spillage. When using cloths, sawdust or oil absorbents, these should be treated as environmental hazardous waste. Follow local regulations.

•Choose an area, preferably with a concrete ﬂoor, when you handle or store oils and fuel so that you can clear up any spillage without it penetrating into the ground.

•Avoid spillage, use a funnel and ﬁll carefully.

•When draining, ensure that a suitably sized container is placed correctly. Remember that the oil does not always run straight down.

•Transfer the waste oil into a sealed container and

Clean the machine regularly

Front securing eyelets

13

Image 14

Contents PT26 D Contents Page Driving and Transport on Public Roads IntroductionCongratulations TowingProper Service Serial NumberSymbols and Decals Important Information Safety Instructions General UseWhen driving Driving on slopes Do as followsMaintenance ChildrenAvoid sparking and its consequences by Other protective devices are not ﬁtted or are defective Transport Environment protectionUser responsibility Presentation Placement of controls Speed control Parking brakeControl panel SeatDifferential Lock Adjusting the cutting heightSteering wheel and steering wheel console FuellingWinter fuel and parafﬁn precipitation Controls on the control panelControl lever hydraulics Lifting the cutting unit transport positionIndicators trafﬁc kit option Switch for operation of cutting unitSwitch for extra hydraulic function hydraulic kit option Push button for horn trafﬁc kit optionThrottle control Starter switchHeadlight High speedRotating warning light trafﬁc kit option Weight transferSpare Power outlet Parking lights trafﬁc kit optionLever for steering wheel console angle Adjusting the steering wheel settingChronometer Rops Cooling system Cutting unit AntifreezeAccessories Driving Mowing TipsBefore Starting Start gas or ether must not be used for this engineStarting the engine Starting with a weak battery Starting in cold conditionsDriving the machine Bleeding in the event of fuel stoppage BrakingCutting the engine Engine stop250 500 1000 2000 MaintenanceMaintenance Schedule 250 500 1000 2000 Cleaning Removing the machine’s covers Cleaning the radiators heat exchangerAdjusting the pump and generator drive belts Checking radiatorgrillesReplacing the pump and generator drive belts Checking and adjusting the throttle controlAdjusting the parking brake Checking the exhaust systemReplacing the air ﬁlter Cleaning the cyclone ﬁlterServicing the air ﬁlter Emptying the particle trapChecking the Tyre Pressures Bleeding the fuel systemServicing the fuel ﬁlter Servicing the battery FusesChecking the Safety System FU2 FU9Replacing the bulb in the headlight Attaching and removing the cutting unit Light settingCutting Unit Components Side shifting the cutting unitImportant Information Setting the cutting height and tilt angle Cutting heightTilt angle Cutting Unit’s Service PositionPlacing in the Service Position Ground pressureReleasing the Service Position Cutting Unit ModelAlways replace the belts in pairs Replacing the power take-off beltsChecking the Blades Replacing the belt on the Combi unit Adjusting the power take-off beltsReplacing the cutting unit belt Removal of BioClip Plug General LubricationLubrication Schedule Lubricating the cablesPivot wheel bearings Handle for cutting height settingLubricating in Accordance with Lubrication Schedule Cutting unit’s bevel gearEngine Oil Power take-off shaft’s front support bearingLift cylinder Viscosity and qualityFilling engine oil Changing the Engine OilInspection off the oil level Replacing the engine’s oil ﬁlterHydraulic oil Filling hydraulic oilLifting arm’s rear bearings Hydraulic oil ﬁlter, changeCutting unit mounting Driver’s SeatParking brake cables Control cylinderLubrication Trouble Shooting Guide Problem CauseProblem Cause Problem Cause Trouble Shooting Guide Storage Winter StorageService Electrical system Hydraulic System Hydraulic System Fuel system Technical Data Data PT 26DTransmission Vibration levels4 Technical Data Diverse design standards Design standardsEU Declaration of Conformity only applies to Europe Design standards Page Page 1153893-26 ´z+Uy@¶6u¨ ´z+Uy@¶6u¨ Original instructions