Husqvarna PT26 D manual Speed control, Parking brake

Page 18

Presentation

	Steering wheel console
40.	Warning lamp Battery charging page 24	47.	Warning lamp High speed page 24
41.	Warning lamp Differential lock page 24	48.	Warning lamp Right-hand indicator page 24
42.	Warning lamp Coolant temperature page 24	49.	Lever for tilting the steering wheel console page 24
43.	Warning lamp Glow plug heating page 24	50.	Warning lamp Full beam page 24
44.	Warning lamp Engine oil pressure page 24	51.	Warning lamp Left-hand indicator page 24

45.Warning lamp Cutting unit operation page 24

46.Warning lamp Parking brake page 24

1-2. Speed control

The speed of the machine is variably controlled using two pedals. Pedal (1) is used to travel forwards and pedal (2) to reverse.

WARNING:

Make sure that no branches can interfere with the pedals when mowing under bushes.

Speed control

3. Parking brake

Apply the parking brake by moving the handle forward.

Release the parking brake by moving the handle back.

Parking brake

17

Image 18

Contents PT26 D Contents Page Driving and Transport on Public Roads IntroductionCongratulations TowingProper Service Serial NumberSymbols and Decals Important Information Safety Instructions General UseWhen driving Driving on slopes Do as followsMaintenance ChildrenAvoid sparking and its consequences by Other protective devices are not ﬁtted or are defective Transport Environment protectionUser responsibility Presentation Placement of controls Speed control Parking brakeControl panel SeatDifferential Lock Adjusting the cutting heightSteering wheel and steering wheel console FuellingWinter fuel and parafﬁn precipitation Controls on the control panelControl lever hydraulics Lifting the cutting unit transport positionIndicators trafﬁc kit option Switch for operation of cutting unitSwitch for extra hydraulic function hydraulic kit option Push button for horn trafﬁc kit optionThrottle control Starter switchHeadlight High speedRotating warning light trafﬁc kit option Weight transferSpare Power outlet Parking lights trafﬁc kit optionAdjusting the steering wheel setting ChronometerLever for steering wheel console angle Rops Cooling system Cutting unit AntifreezeAccessories Driving Mowing TipsBefore Starting Start gas or ether must not be used for this engineStarting the engine Starting with a weak battery Starting in cold conditionsDriving the machine Bleeding in the event of fuel stoppage BrakingCutting the engine Engine stopMaintenance Maintenance Schedule250 500 1000 2000 250 500 1000 2000 Cleaning Removing the machine’s covers Cleaning the radiators heat exchangerAdjusting the pump and generator drive belts Checking radiatorgrillesReplacing the pump and generator drive belts Checking and adjusting the throttle controlAdjusting the parking brake Checking the exhaust systemReplacing the air ﬁlter Cleaning the cyclone ﬁlterServicing the air ﬁlter Emptying the particle trapBleeding the fuel system Servicing the fuel ﬁlterChecking the Tyre Pressures Servicing the battery FusesChecking the Safety System FU2 FU9Replacing the bulb in the headlight Attaching and removing the cutting unit Light settingCutting Unit Components Side shifting the cutting unitImportant Information Setting the cutting height and tilt angle Cutting heightTilt angle Cutting Unit’s Service PositionPlacing in the Service Position Ground pressureReleasing the Service Position Cutting Unit ModelReplacing the power take-off belts Checking the BladesAlways replace the belts in pairs Adjusting the power take-off belts Replacing the cutting unit beltReplacing the belt on the Combi unit Removal of BioClip Plug General LubricationLubrication Schedule Lubricating the cablesPivot wheel bearings Handle for cutting height settingLubricating in Accordance with Lubrication Schedule Cutting unit’s bevel gearEngine Oil Power take-off shaft’s front support bearingLift cylinder Viscosity and qualityFilling engine oil Changing the Engine OilInspection off the oil level Replacing the engine’s oil ﬁlterHydraulic oil Filling hydraulic oilLifting arm’s rear bearings Hydraulic oil ﬁlter, changeCutting unit mounting Driver’s SeatParking brake cables Control cylinderLubrication Trouble Shooting Guide Problem CauseProblem Cause Problem Cause Trouble Shooting Guide Storage Winter StorageService Electrical system Hydraulic System Hydraulic System Fuel system Technical Data Data PT 26DTransmission Vibration levels4 Technical Data Design standards EU Declaration of Conformity only applies to EuropeDiverse design standards Design standards Page Page 1153893-26 ´z+Uy@¶6u¨ ´z+Uy@¶6u¨ Original instructions