Husqvarna PT26 D manual 250 500 1000 2000

Page 37

Maintenance

● = Described in this manual

❍ = Not described in this manual.

Maintenance	Page	Daily main-		Weekly	Maintenance interval hours
		tenance		main-	250	500	1000		2000 3000
		befor after		tenance	250	500	1000		2000 3000
		befor after


Check the condition of the battery,	42				●
clean if necessary

Check the oil level in the bevel gear,	112				●
top up if necessary

Check the wheel nuts	-				❍

Check the parking brake, adjust if	39				●
necessary5
Check the safety function	43				●

Check/adjust the cutting unit settings.	47				●
(tilt angle)5
Replace the air ﬁlter and clean the	40					●
cyclone ﬁlter

Replace the belts (power take-off belt	-					●
and cutting unit belt)
Adjust the power take-off belts5
Check the condition of the hydraulic	-					❍
hoses5
Replace fuel ﬁlter and check hoses4	-					❍
Adjust the valves and check the	-						❍
engine speed4
Replace the pump and generator belt	39						●

Change the hydraulic oil and ﬁlter4	-						❍
Change the oil in the bevel gear	112					●

Change the coolant4	50						●
Check all hoses with connections to	-								❍
the engine and the engine’s
mountings5
Replace the diaphragm for the closed	-								❍
crankcase ventilation4
Check cables and terminals in the	-									❍
electrical system4
Check generator and starter motor4	-									❍
Pressure test the fuel injection	-									❍
nozzles4
Check the coolant pump4	-									❍

1.First change after 25 hours. When operating with a heavy load or at high ambient temperatures, replace the engine oil every 125 hours.

36

Image 37

Contents PT26 D Contents Page Congratulations IntroductionDriving and Transport on Public Roads TowingSerial Number Proper ServiceSymbols and Decals Important Information General Use Safety InstructionsWhen driving Do as follows Driving on slopesChildren MaintenanceAvoid sparking and its consequences by Other protective devices are not ﬁtted or are defective Environment protection TransportUser responsibility Presentation Placement of controls Parking brake Speed controlSeat Control panelSteering wheel and steering wheel console Adjusting the cutting heightDifferential Lock FuellingControl lever hydraulics Controls on the control panelWinter fuel and parafﬁn precipitation Lifting the cutting unit transport positionSwitch for extra hydraulic function hydraulic kit option Switch for operation of cutting unitIndicators trafﬁc kit option Push button for horn trafﬁc kit optionHeadlight Starter switchThrottle control High speedSpare Power outlet Weight transferRotating warning light trafﬁc kit option Parking lights trafﬁc kit optionChronometer Adjusting the steering wheel settingLever for steering wheel console angle Rops Cooling system Antifreeze Cutting unitAccessories Mowing Tips DrivingStart gas or ether must not be used for this engine Before StartingStarting the engine Starting in cold conditions Starting with a weak batteryDriving the machine Cutting the engine BrakingBleeding in the event of fuel stoppage Engine stopMaintenance Schedule Maintenance250 500 1000 2000 250 500 1000 2000 Cleaning Adjusting the pump and generator drive belts Cleaning the radiators heat exchangerRemoving the machine’s covers Checking radiatorgrillesAdjusting the parking brake Checking and adjusting the throttle controlReplacing the pump and generator drive belts Checking the exhaust systemServicing the air ﬁlter Cleaning the cyclone ﬁlterReplacing the air ﬁlter Emptying the particle trapServicing the fuel ﬁlter Bleeding the fuel systemChecking the Tyre Pressures Fuses Servicing the batteryFU2 FU9 Checking the Safety SystemReplacing the bulb in the headlight Cutting Unit Components Light settingAttaching and removing the cutting unit Side shifting the cutting unitImportant Information Cutting height Setting the cutting height and tilt anglePlacing in the Service Position Cutting Unit’s Service PositionTilt angle Ground pressureCutting Unit Model Releasing the Service PositionChecking the Blades Replacing the power take-off beltsAlways replace the belts in pairs Replacing the cutting unit belt Adjusting the power take-off beltsReplacing the belt on the Combi unit Removal of BioClip Plug Lubrication Schedule LubricationGeneral Lubricating the cablesLubricating in Accordance with Lubrication Schedule Handle for cutting height settingPivot wheel bearings Cutting unit’s bevel gearLift cylinder Power take-off shaft’s front support bearingEngine Oil Viscosity and qualityChanging the Engine Oil Filling engine oilHydraulic oil Replacing the engine’s oil ﬁlterInspection off the oil level Filling hydraulic oilCutting unit mounting Hydraulic oil ﬁlter, changeLifting arm’s rear bearings Driver’s SeatControl cylinder Parking brake cablesLubrication Problem Cause Trouble Shooting GuideProblem Cause Problem Cause Trouble Shooting Guide Winter Storage StorageService Electrical system Hydraulic System Hydraulic System Fuel system Data PT 26D Technical DataTransmission Vibration levels4 Technical Data EU Declaration of Conformity only applies to Europe Design standardsDiverse design standards Design standards Page Page Original instructions 1153893-26 ´z+Uy@¶6u¨ ´z+Uy@¶6u¨