Husqvarna PT26 D Braking, Cutting the engine, Bleeding in the event of fuel stoppage, Engine stop

Page 35

Driving

5.Activate weight transfer if desired using the switch (30) on the control panel. The weight transfer position must always be activated when driving up slopes

and deactivated when driving down slopes.

6. Start the cutting unit as necessary using the switch for power take-off (22) on the control panel.

The cutting unit can only be started in low speed. If the switch has already been pulled out and the unit does not start, press it in and pull it out again (See safety circuit on page 42).

Switch for power take-off and weight transfer

Braking

Release the drive pedals. The machine slows and is stopped by the drive system. Do not use the parking brake as the drive brake.

Quicker braking is possible if you press down the drive pedal for the opposite direction.

Cutting the engine

If the engine has been worked hard, it is preferable to let the engine idle for a minute so it is running at its normal working temperature when it is stopped.

1.Switch off the cutting unit if it is running.

2.Lift the cutting unit using the lifting lever.

3.Move the throttle control to the “MIN” position. Turn the ignition key to “OFF”.

4.Apply the parking brake, when the machine is stationary, by ﬁrst pulling up the lock handle (36) on the control panel and then press down the parking brake pedal (3).

Bleeding in the event of fuel stoppage.

See the chapter, Maintenance “Bleeding the fuel system” on page 86.

Engine stop

If the engine stops, it is still possible to steer, but the wheel is heavy to turn. As the transmission is hydrostatic the machine stops immediately.

Switch off the cutting unit

Stop position

Parking brake

34

Image 35

Contents PT26 D Contents Page Towing IntroductionCongratulations Driving and Transport on Public RoadsSerial Number Proper ServiceSymbols and Decals Important Information General Use Safety InstructionsWhen driving Do as follows Driving on slopesChildren MaintenanceAvoid sparking and its consequences by Other protective devices are not ﬁtted or are defective Environment protection TransportUser responsibility Presentation Placement of controls Parking brake Speed controlSeat Control panelFuelling Adjusting the cutting heightSteering wheel and steering wheel console Differential LockLifting the cutting unit transport position Controls on the control panelControl lever hydraulics Winter fuel and parafﬁn precipitationPush button for horn trafﬁc kit option Switch for operation of cutting unitSwitch for extra hydraulic function hydraulic kit option Indicators trafﬁc kit optionHigh speed Starter switchHeadlight Throttle controlParking lights trafﬁc kit option Weight transferSpare Power outlet Rotating warning light trafﬁc kit optionLever for steering wheel console angle Adjusting the steering wheel settingChronometer Rops Cooling system Antifreeze Cutting unitAccessories Mowing Tips DrivingStart gas or ether must not be used for this engine Before StartingStarting the engine Starting in cold conditions Starting with a weak batteryDriving the machine Engine stop BrakingCutting the engine Bleeding in the event of fuel stoppage250 500 1000 2000 MaintenanceMaintenance Schedule 250 500 1000 2000 Cleaning Checking radiatorgrilles Cleaning the radiators heat exchangerAdjusting the pump and generator drive belts Removing the machine’s coversChecking the exhaust system Checking and adjusting the throttle controlAdjusting the parking brake Replacing the pump and generator drive beltsEmptying the particle trap Cleaning the cyclone ﬁlterServicing the air ﬁlter Replacing the air ﬁlterChecking the Tyre Pressures Bleeding the fuel systemServicing the fuel ﬁlter Fuses Servicing the batteryFU2 FU9 Checking the Safety SystemReplacing the bulb in the headlight Side shifting the cutting unit Light settingCutting Unit Components Attaching and removing the cutting unitImportant Information Cutting height Setting the cutting height and tilt angleGround pressure Cutting Unit’s Service PositionPlacing in the Service Position Tilt angleCutting Unit Model Releasing the Service PositionAlways replace the belts in pairs Replacing the power take-off beltsChecking the Blades Replacing the belt on the Combi unit Adjusting the power take-off beltsReplacing the cutting unit belt Removal of BioClip Plug Lubricating the cables LubricationLubrication Schedule GeneralCutting unit’s bevel gear Handle for cutting height settingLubricating in Accordance with Lubrication Schedule Pivot wheel bearingsViscosity and quality Power take-off shaft’s front support bearingLift cylinder Engine OilChanging the Engine Oil Filling engine oilFilling hydraulic oil Replacing the engine’s oil ﬁlterHydraulic oil Inspection off the oil levelDriver’s Seat Hydraulic oil ﬁlter, changeCutting unit mounting Lifting arm’s rear bearingsControl cylinder Parking brake cablesLubrication Problem Cause Trouble Shooting GuideProblem Cause Problem Cause Trouble Shooting Guide Winter Storage StorageService Electrical system Hydraulic System Hydraulic System Fuel system Data PT 26D Technical DataTransmission Vibration levels4 Technical Data Diverse design standards Design standardsEU Declaration of Conformity only applies to Europe Design standards Page Page Original instructions 1153893-26 ´z+Uy@¶6u¨ ´z+Uy@¶6u¨