Husqvarna PT26 D manual Safety Instructions, General Use

Page 8

Safety Instructions

Chapter 3: Safety Instructions

These instructions are for your safety. Read them carefully.

General Use

Read all instructions in this operator’s manual and on the machine before starting it. Ensure you understand them and then observe them.

Learn how to use the machine and its controls safely and learn how to stop quickly. Also learn to recognise the safety decals.

If you get into a situation where you feel unsure about how to progress, stop and seek expert advice. Contact your Husqvarna retailer, service agent or an experienced user. Avoid all usage that you consider to be beyond your capability.

Only allow the machine to be used by adults who are familiar with its use.

Make sure nobody else is in the vicinity of the machine when you start the engine, engage the drive, or run the machine.

Clear the area of objects such as stones, toys, steel wire, etc. that may become caught in the blades and thrown out.

Beware of the rear ejector and do not point it at any one.

Stop the engine and prevent it from starting before you clean the cutting unit.

Remember that the driver is responsible for dangers or accidents.

Never carry passengers. The machine is only intended to be used by one person.

Always look down and behind before and during reversing manoeuvres. Keep watch for both large and small obstacles.

Slow down before turning.

Read the operator’s manual before starting the machine

Clear the area of objects before mowing

Never take passengers

7

Image 8
Contents PT26 D Contents Page Introduction CongratulationsDriving and Transport on Public Roads TowingProper Service Serial NumberSymbols and Decals Important Information Safety Instructions General UseWhen driving Driving on slopes Do as followsMaintenance ChildrenAvoid sparking and its consequences by Other protective devices are not fitted or are defective Transport Environment protectionUser responsibility Presentation Placement of controls Speed control Parking brakeControl panel SeatAdjusting the cutting height Steering wheel and steering wheel consoleDifferential Lock FuellingControls on the control panel Control lever hydraulicsWinter fuel and paraffin precipitation Lifting the cutting unit transport positionSwitch for operation of cutting unit Switch for extra hydraulic function hydraulic kit optionIndicators traffic kit option Push button for horn traffic kit optionStarter switch HeadlightThrottle control High speedWeight transfer Spare Power outletRotating warning light traffic kit option Parking lights traffic kit optionLever for steering wheel console angle Adjusting the steering wheel settingChronometer Rops Cooling system Cutting unit AntifreezeAccessories Driving Mowing TipsBefore Starting Start gas or ether must not be used for this engineStarting the engine Starting with a weak battery Starting in cold conditionsDriving the machine Braking Cutting the engineBleeding in the event of fuel stoppage Engine stop250 500 1000 2000 MaintenanceMaintenance Schedule 250 500 1000 2000 Cleaning Cleaning the radiators heat exchanger Adjusting the pump and generator drive beltsRemoving the machine’s covers Checking radiatorgrillesChecking and adjusting the throttle control Adjusting the parking brakeReplacing the pump and generator drive belts Checking the exhaust systemCleaning the cyclone filter Servicing the air filterReplacing the air filter Emptying the particle trapChecking the Tyre Pressures Bleeding the fuel systemServicing the fuel filter Servicing the battery FusesChecking the Safety System FU2 FU9Replacing the bulb in the headlight Light setting Cutting Unit ComponentsAttaching and removing the cutting unit Side shifting the cutting unitImportant Information Setting the cutting height and tilt angle Cutting heightCutting Unit’s Service Position Placing in the Service PositionTilt angle Ground pressureReleasing the Service Position Cutting Unit ModelAlways replace the belts in pairs Replacing the power take-off beltsChecking the Blades Replacing the belt on the Combi unit Adjusting the power take-off beltsReplacing the cutting unit belt Removal of BioClip Plug Lubrication Lubrication ScheduleGeneral Lubricating the cablesHandle for cutting height setting Lubricating in Accordance with Lubrication SchedulePivot wheel bearings Cutting unit’s bevel gearPower take-off shaft’s front support bearing Lift cylinderEngine Oil Viscosity and qualityFilling engine oil Changing the Engine OilReplacing the engine’s oil filter Hydraulic oilInspection off the oil level Filling hydraulic oilHydraulic oil filter, change Cutting unit mountingLifting arm’s rear bearings Driver’s SeatParking brake cables Control cylinderLubrication Trouble Shooting Guide Problem CauseProblem Cause Problem Cause Trouble Shooting Guide Storage Winter StorageService Electrical system Hydraulic System Hydraulic System Fuel system Technical Data Data PT 26DTransmission Vibration levels4 Technical Data Diverse design standards Design standardsEU Declaration of Conformity only applies to Europe Design standards Page Page 1153893-26 ´z+Uy@¶6u¨ ´z+Uy@¶6u¨ Original instructions