Husqvarna PT26 D manual Lubrication Schedule, General, Lubricating the cables

Page 54

Lubrication

Chapter 7: Lubrication

Lubrication Schedule

When in daily use, the weekly lubrication (40 h) schedule should be carried out twice a week.

General

The position numbers for the lubrication points refer to the lubrication instructions on the following pages.

Remove the ignition key to prevent unintentional movements during lubrication.

When lubricating with an oilcan, it ought to be ﬁlled with engine oil. When lubricating with grease, unless otherwise stated, grease 503 98 96-01 or another chassis or ball bearing grease offering good corrosion protection shall be used.

With daily use, the machine shall be lubricated twice weekly.

Wipe away excess grease after lubrication.

Lubricating the cables

Grease both ends of the cables and move the controls to end stop positions when lubricating. Re-attach the rubber covers on the cables after lubrication. Cables with sheaths will jam if they are not lubricated regularly. A jammed cable may cause malfunction, such as the parking braking being applied.

= Filter replacement

= Oil Change

= Level check

= Brush

= Grease nipple

= Oil can

Symbols on the lubrication chart

A. Radiator grille, See “Checking radiatorgrilles” on page 79.

B. Pump and alternator belt, See “Replacing the pump and generator drive belts” on page 81.

C. Power take-off belts, See “Replacing the power take-off belts” on page 105.

D. Coolant, See “Cooling system” on page 50.

E. Cutting unit belt, See “Replacing the cutting unit belt” on page 107.

F. Air filter, See “Servicing the air filter” on page 84.

G. Fuel filter, See “Servicing the fuel filter” on page 87.

53

Image 54

Contents PT26 D Contents Page Driving and Transport on Public Roads IntroductionCongratulations TowingProper Service Serial NumberSymbols and Decals Important Information Safety Instructions General UseWhen driving Driving on slopes Do as followsMaintenance ChildrenAvoid sparking and its consequences by Other protective devices are not ﬁtted or are defective Transport Environment protectionUser responsibility Presentation Placement of controls Speed control Parking brakeControl panel SeatDifferential Lock Adjusting the cutting heightSteering wheel and steering wheel console FuellingWinter fuel and parafﬁn precipitation Controls on the control panelControl lever hydraulics Lifting the cutting unit transport positionIndicators trafﬁc kit option Switch for operation of cutting unitSwitch for extra hydraulic function hydraulic kit option Push button for horn trafﬁc kit optionThrottle control Starter switchHeadlight High speedRotating warning light trafﬁc kit option Weight transferSpare Power outlet Parking lights trafﬁc kit optionAdjusting the steering wheel setting ChronometerLever for steering wheel console angle Rops Cooling system Cutting unit AntifreezeAccessories Driving Mowing TipsBefore Starting Start gas or ether must not be used for this engineStarting the engine Starting with a weak battery Starting in cold conditionsDriving the machine Bleeding in the event of fuel stoppage BrakingCutting the engine Engine stopMaintenance Maintenance Schedule250 500 1000 2000 250 500 1000 2000 Cleaning Removing the machine’s covers Cleaning the radiators heat exchangerAdjusting the pump and generator drive belts Checking radiatorgrillesReplacing the pump and generator drive belts Checking and adjusting the throttle controlAdjusting the parking brake Checking the exhaust systemReplacing the air ﬁlter Cleaning the cyclone ﬁlterServicing the air ﬁlter Emptying the particle trapBleeding the fuel system Servicing the fuel ﬁlterChecking the Tyre Pressures Servicing the battery FusesChecking the Safety System FU2 FU9Replacing the bulb in the headlight Attaching and removing the cutting unit Light settingCutting Unit Components Side shifting the cutting unitImportant Information Setting the cutting height and tilt angle Cutting heightTilt angle Cutting Unit’s Service PositionPlacing in the Service Position Ground pressureReleasing the Service Position Cutting Unit ModelReplacing the power take-off belts Checking the BladesAlways replace the belts in pairs Adjusting the power take-off belts Replacing the cutting unit beltReplacing the belt on the Combi unit Removal of BioClip Plug General LubricationLubrication Schedule Lubricating the cablesPivot wheel bearings Handle for cutting height settingLubricating in Accordance with Lubrication Schedule Cutting unit’s bevel gearEngine Oil Power take-off shaft’s front support bearingLift cylinder Viscosity and qualityFilling engine oil Changing the Engine OilInspection off the oil level Replacing the engine’s oil ﬁlterHydraulic oil Filling hydraulic oilLifting arm’s rear bearings Hydraulic oil ﬁlter, changeCutting unit mounting Driver’s SeatParking brake cables Control cylinderLubrication Trouble Shooting Guide Problem CauseProblem Cause Problem Cause Trouble Shooting Guide Storage Winter StorageService Electrical system Hydraulic System Hydraulic System Fuel system Technical Data Data PT 26DTransmission Vibration levels4 Technical Data Design standards EU Declaration of Conformity only applies to EuropeDiverse design standards Design standards Page Page 1153893-26 ´z+Uy@¶6u¨ ´z+Uy@¶6u¨ Original instructions