Husqvarna PT26 D Switch for operation of cutting unit, Push button for horn trafﬁc kit option

Page 22

Presentation

Other functions (option)

When the lever is moved laterally, the oil pressure is operated to the 2nd hydraulic function, the terminals are under the foot plate hatch.

22. Switch for operation of cutting unit

The cutting unit can only be started when the driver is sitting in the seat.

•Pull out the switch to engage cutting unit operation.

• Press in the switch to disengage cutting unit operation.

If the safety circuit trips cutting unit operation, the switch must be pressed in and pulled out again.

The safety circuit trips and the cutting unit stops:

When the cutting unit is raised to the uppermostSwitch for operation of cutting unit position

When the driver leaves the seat. There is a brief delay to prevent stoppages should the driver bounce in the seat When high gear is engaged.

When the starter is activated.

23. Switch for extra hydraulic function (hydraulic kit option)

The switch is used, among others, when steering the folding plough for individual control of the left or right- hand plough-blades. Operate the plough blade using the lever (21).

Switch for extra 12 V outlet

24. Push button for horn (trafﬁc kit option)

Switch for horn

25. Indicators (trafﬁc kit option)

Press for the left-hand or right-hand indicator. Blinkers are switched off automatically after approximately 30 seconds or manually by pressing in the same direction. A new 30 second period is activated if you press after the blinkers have been switched off. Pressing in the opposite direction while ﬂashing, activates the blinkers for the opposite side for

30 seconds.

Switch for indicators

21

Image 22

Contents PT26 D Contents Page Driving and Transport on Public Roads IntroductionCongratulations TowingProper Service Serial NumberSymbols and Decals Important Information Safety Instructions General UseWhen driving Driving on slopes Do as followsMaintenance ChildrenAvoid sparking and its consequences by Other protective devices are not ﬁtted or are defective Transport Environment protectionUser responsibility Presentation Placement of controls Speed control Parking brakeControl panel SeatDifferential Lock Adjusting the cutting heightSteering wheel and steering wheel console FuellingWinter fuel and parafﬁn precipitation Controls on the control panelControl lever hydraulics Lifting the cutting unit transport positionIndicators trafﬁc kit option Switch for operation of cutting unitSwitch for extra hydraulic function hydraulic kit option Push button for horn trafﬁc kit optionThrottle control Starter switchHeadlight High speedRotating warning light trafﬁc kit option Weight transferSpare Power outlet Parking lights trafﬁc kit optionChronometer Adjusting the steering wheel settingLever for steering wheel console angle Rops Cooling system Cutting unit AntifreezeAccessories Driving Mowing TipsBefore Starting Start gas or ether must not be used for this engineStarting the engine Starting with a weak battery Starting in cold conditionsDriving the machine Bleeding in the event of fuel stoppage BrakingCutting the engine Engine stopMaintenance Schedule Maintenance250 500 1000 2000 250 500 1000 2000 Cleaning Removing the machine’s covers Cleaning the radiators heat exchangerAdjusting the pump and generator drive belts Checking radiatorgrillesReplacing the pump and generator drive belts Checking and adjusting the throttle controlAdjusting the parking brake Checking the exhaust systemReplacing the air ﬁlter Cleaning the cyclone ﬁlterServicing the air ﬁlter Emptying the particle trapServicing the fuel ﬁlter Bleeding the fuel systemChecking the Tyre Pressures Servicing the battery FusesChecking the Safety System FU2 FU9Replacing the bulb in the headlight Attaching and removing the cutting unit Light settingCutting Unit Components Side shifting the cutting unitImportant Information Setting the cutting height and tilt angle Cutting heightTilt angle Cutting Unit’s Service PositionPlacing in the Service Position Ground pressureReleasing the Service Position Cutting Unit ModelChecking the Blades Replacing the power take-off beltsAlways replace the belts in pairs Replacing the cutting unit belt Adjusting the power take-off beltsReplacing the belt on the Combi unit Removal of BioClip Plug General LubricationLubrication Schedule Lubricating the cablesPivot wheel bearings Handle for cutting height settingLubricating in Accordance with Lubrication Schedule Cutting unit’s bevel gearEngine Oil Power take-off shaft’s front support bearingLift cylinder Viscosity and qualityFilling engine oil Changing the Engine OilInspection off the oil level Replacing the engine’s oil ﬁlterHydraulic oil Filling hydraulic oilLifting arm’s rear bearings Hydraulic oil ﬁlter, changeCutting unit mounting Driver’s SeatParking brake cables Control cylinderLubrication Trouble Shooting Guide Problem CauseProblem Cause Problem Cause Trouble Shooting Guide Storage Winter StorageService Electrical system Hydraulic System Hydraulic System Fuel system Technical Data Data PT 26DTransmission Vibration levels4 Technical Data EU Declaration of Conformity only applies to Europe Design standardsDiverse design standards Design standards Page Page 1153893-26 ´z+Uy@¶6u¨ ´z+Uy@¶6u¨ Original instructions