Husqvarna PT26 D manual Transmission

Page 73

Technical Data

Data	PT 26D


Hydraulic System

Max. working pressure	210 bar/3050 PSI

Power steering circuit max. working pressure	120 bar/1740 PSI

Transmission	Hydrostatic

Manufacturer and type	Pump Danfoss LPV25 25 cc variable annular piston
	Front Sauer-Danfoss OEMV 160 cc
	Rear Sauer-Danfoss OEMV 125 cc

Oil	ISO VG 46 cSt

Oil volume, total including hydraulic system	13 litres

Maximum speed

Forwards, high speed	18 km/h

Forwards, low speed	13 km/h

Reverse, low speed	13 km/h

Max inclination, all directions	10°

Cutting unit	Combi 155

Cutting width	1550 mm/61"

Cutting heights	25.4 - 127 mm / 1" - 5"

Blade length	560 mm/22"

Width	1610 mm / 5.28 ft

Weight	113 kg / 248 lb

Length machine with unit	approximately 2800 mm / 9.19 ft

Bevel gear, oil volume	0.6 litres

Cutting unit	Combi 132

Cutting width	1300 mm / 51.2"

Cutting heights	25.4 - 127 mm / 1" - 5"

Blade length	490 mm/19.3"

Width	1340 mm / 52.8"

Weight	approximately 100 kg / 29.3lb

Length machine with unit	approximately 2730 mm / 8.96 ft

Bevel gear, oil volume	0.6 litres

72

Image 73

Contents PT26 D Contents Page Congratulations IntroductionDriving and Transport on Public Roads TowingSerial Number Proper ServiceSymbols and Decals Important Information General Use Safety InstructionsWhen driving Do as follows Driving on slopesChildren MaintenanceAvoid sparking and its consequences by Other protective devices are not ﬁtted or are defective Environment protection TransportUser responsibility Presentation Placement of controls Parking brake Speed controlSeat Control panelSteering wheel and steering wheel console Adjusting the cutting heightDifferential Lock FuellingControl lever hydraulics Controls on the control panelWinter fuel and parafﬁn precipitation Lifting the cutting unit transport positionSwitch for extra hydraulic function hydraulic kit option Switch for operation of cutting unitIndicators trafﬁc kit option Push button for horn trafﬁc kit optionHeadlight Starter switchThrottle control High speedSpare Power outlet Weight transferRotating warning light trafﬁc kit option Parking lights trafﬁc kit optionChronometer Adjusting the steering wheel settingLever for steering wheel console angle Rops Cooling system Antifreeze Cutting unitAccessories Mowing Tips DrivingStart gas or ether must not be used for this engine Before StartingStarting the engine Starting in cold conditions Starting with a weak batteryDriving the machine Cutting the engine BrakingBleeding in the event of fuel stoppage Engine stopMaintenance Schedule Maintenance250 500 1000 2000 250 500 1000 2000 Cleaning Adjusting the pump and generator drive belts Cleaning the radiators heat exchangerRemoving the machine’s covers Checking radiatorgrillesAdjusting the parking brake Checking and adjusting the throttle controlReplacing the pump and generator drive belts Checking the exhaust systemServicing the air ﬁlter Cleaning the cyclone ﬁlterReplacing the air ﬁlter Emptying the particle trapServicing the fuel ﬁlter Bleeding the fuel systemChecking the Tyre Pressures Fuses Servicing the batteryFU2 FU9 Checking the Safety SystemReplacing the bulb in the headlight Cutting Unit Components Light settingAttaching and removing the cutting unit Side shifting the cutting unitImportant Information Cutting height Setting the cutting height and tilt anglePlacing in the Service Position Cutting Unit’s Service PositionTilt angle Ground pressureCutting Unit Model Releasing the Service PositionChecking the Blades Replacing the power take-off beltsAlways replace the belts in pairs Replacing the cutting unit belt Adjusting the power take-off beltsReplacing the belt on the Combi unit Removal of BioClip Plug Lubrication Schedule LubricationGeneral Lubricating the cablesLubricating in Accordance with Lubrication Schedule Handle for cutting height settingPivot wheel bearings Cutting unit’s bevel gearLift cylinder Power take-off shaft’s front support bearingEngine Oil Viscosity and qualityChanging the Engine Oil Filling engine oilHydraulic oil Replacing the engine’s oil ﬁlterInspection off the oil level Filling hydraulic oilCutting unit mounting Hydraulic oil ﬁlter, changeLifting arm’s rear bearings Driver’s SeatControl cylinder Parking brake cablesLubrication Problem Cause Trouble Shooting GuideProblem Cause Problem Cause Trouble Shooting Guide Winter Storage StorageService Electrical system Hydraulic System Hydraulic System Fuel system Data PT 26D Technical DataTransmission Vibration levels4 Technical Data EU Declaration of Conformity only applies to Europe Design standardsDiverse design standards Design standards Page Page Original instructions 1153893-26 ´z+Uy@¶6u¨ ´z+Uy@¶6u¨