Husqvarna PT26 D manual Children, Maintenance

Page 11

Safety Instructions

Children

• Serious accidents may occur if you fail to be on guard for children in the vicinity of the machine. Children are often attracted to the machine and mowing. Never assume that children will stay put where you last saw them.

• Keep children away from the mowing area and under close supervision by another adult.

• Keep an eye out and shut off the machine if children enter the work area.

• Before and during a reversing manoeuvre, look

backward and downward for small children.

• Never allow a child to ride with you. They can fall

Never allow children to operate the machine

off and seriously injure themselves or be in the way

 

for safe manoeuvring of the machine.

 

• Never allow children to operate the machine.

 

• Be particularly careful near corners, bushes, trees

 

or other objects that block your view.

 

Maintenance

 

• Stop the engine. Remove the ignition key before

 

making any adjustments or carrying out

 

maintenance.

 

• Never fill the fuel tank indoors.

 

• Only store fuel in clean containers approved for the

 

purpose.

 

• Never remove the fuel cap or fill the fuel tank with

 

fuel while the engine is running.

 

• Allow the engine to cool before refuelling. Do not

 

smoke.

 

• Handle oil, oil filters, fuel and the battery carefully,

Never fill the fuel tank indoors

of environmental considerations. Observe

 

applicable recycling regulations.

 

•Do not allow compressed air to come into contact with skin. If compressed air penetrates the skin, seek medical advice immediately.

•Seek medical advice immediately if skin comes into contact with fuel, which that is under high pressure.

•The combustible material in some of the engine’s components (e.g. certain seals) can be very dangerous if ignited. Never allow burnt material to come into contact with skin or eyes.

•Do not remove the filler cap or any other component on the cooling system when the engine is hot or under pressure, as hazardous hot coolant can spray out.

10

Page 10 Page 12
Image 11
Page 10 Page 12
Contents PT26 D Contents Page Towing IntroductionCongratulations Driving and Transport on Public RoadsSerial Number Proper ServiceSymbols and Decals Important Information General Use Safety InstructionsWhen driving Do as follows Driving on slopesChildren MaintenanceAvoid sparking and its consequences by Other protective devices are not fitted or are defective Environment protection TransportUser responsibility Presentation Placement of controls Parking brake Speed controlSeat Control panelFuelling Adjusting the cutting heightSteering wheel and steering wheel console Differential LockLifting the cutting unit transport position Controls on the control panelControl lever hydraulics Winter fuel and paraffin precipitationPush button for horn traffic kit option Switch for operation of cutting unitSwitch for extra hydraulic function hydraulic kit option Indicators traffic kit optionHigh speed Starter switchHeadlight Throttle controlParking lights traffic kit option Weight transferSpare Power outlet Rotating warning light traffic kit optionLever for steering wheel console angle Adjusting the steering wheel settingChronometer Rops Cooling system Antifreeze Cutting unitAccessories Mowing Tips DrivingStart gas or ether must not be used for this engine Before StartingStarting the engine Starting in cold conditions Starting with a weak batteryDriving the machine Engine stop BrakingCutting the engine Bleeding in the event of fuel stoppage250 500 1000 2000 MaintenanceMaintenance Schedule 250 500 1000 2000 Cleaning Checking radiatorgrilles Cleaning the radiators heat exchangerAdjusting the pump and generator drive belts Removing the machine’s coversChecking the exhaust system Checking and adjusting the throttle controlAdjusting the parking brake Replacing the pump and generator drive beltsEmptying the particle trap Cleaning the cyclone filterServicing the air filter Replacing the air filterChecking the Tyre Pressures Bleeding the fuel systemServicing the fuel filter Fuses Servicing the batteryFU2 FU9 Checking the Safety SystemReplacing the bulb in the headlight Side shifting the cutting unit Light settingCutting Unit Components Attaching and removing the cutting unitImportant Information Cutting height Setting the cutting height and tilt angleGround pressure Cutting Unit’s Service PositionPlacing in the Service Position Tilt angleCutting Unit Model Releasing the Service PositionAlways replace the belts in pairs Replacing the power take-off beltsChecking the Blades Replacing the belt on the Combi unit Adjusting the power take-off beltsReplacing the cutting unit belt Removal of BioClip Plug Lubricating the cables LubricationLubrication Schedule GeneralCutting unit’s bevel gear Handle for cutting height settingLubricating in Accordance with Lubrication Schedule Pivot wheel bearingsViscosity and quality Power take-off shaft’s front support bearingLift cylinder Engine OilChanging the Engine Oil Filling engine oilFilling hydraulic oil Replacing the engine’s oil filterHydraulic oil Inspection off the oil levelDriver’s Seat Hydraulic oil filter, changeCutting unit mounting Lifting arm’s rear bearingsControl cylinder Parking brake cablesLubrication Problem Cause Trouble Shooting GuideProblem Cause Problem Cause Trouble Shooting Guide Winter Storage StorageService Electrical system Hydraulic System Hydraulic System Fuel system Data PT 26D Technical DataTransmission Vibration levels4 Technical Data Diverse design standards Design standardsEU Declaration of Conformity only applies to Europe Design standards Page Page Original instructions 1153893-26 ´z+Uy@¶6u¨ ´z+Uy@¶6u¨
Top Page Image Contents