Husqvarna PT26 D manual Lift cylinder, Power take-off shaft’s front support bearing, Engine Oil

Page 56

Lubrication

5. Lift cylinder

2 nipples, one at each end of the cylinder. Lubricate using a grease gun until grease is forced out.

Lift cylinder

6. The power take-off shaft’s front support bearing

Lubricate using a grease gun until grease is forced out.

The power take-off shaft’s front support bearing

7. Engine Oil

Viscosity and quality

Use engine oil viscosity as illustrated, class API CH4 or ACEA E5 or higher.

The engine holds 2.5 litres of oil excluding the ﬁlter (including ﬁlter 2.7 litres).

0W

5W 20

10W 30

15W 40

20W 50

20

30

40

-30	-20	-10	0	10	20	30	40	50 C
-22	-4	-14	32	50	68	86	104	122 F

Viscosity chart

Checking the oil level

Check the oil level in the engine when the machine is standing horizontally with the engine switched off.

Remove the dipstick and wipe it clean. Then insert the dipstick again.

Take the dipstick out again and read the oil level.

The engine dipstick

The oil level should be between the markings on the dipstick. If the level is approaching the “ADD” mark, lower notch, top up the oil to the “FULL” mark, upper notch on the dipstick.

55

Image 56

Contents PT26 D Contents Page Introduction CongratulationsDriving and Transport on Public Roads TowingProper Service Serial NumberSymbols and Decals Important Information Safety Instructions General UseWhen driving Driving on slopes Do as followsMaintenance ChildrenAvoid sparking and its consequences by Other protective devices are not ﬁtted or are defective Transport Environment protectionUser responsibility Presentation Placement of controls Speed control Parking brakeControl panel SeatAdjusting the cutting height Steering wheel and steering wheel consoleDifferential Lock FuellingControls on the control panel Control lever hydraulicsWinter fuel and parafﬁn precipitation Lifting the cutting unit transport positionSwitch for operation of cutting unit Switch for extra hydraulic function hydraulic kit optionIndicators trafﬁc kit option Push button for horn trafﬁc kit optionStarter switch HeadlightThrottle control High speedWeight transfer Spare Power outletRotating warning light trafﬁc kit option Parking lights trafﬁc kit optionLever for steering wheel console angle Adjusting the steering wheel settingChronometer Rops Cooling system Cutting unit AntifreezeAccessories Driving Mowing TipsBefore Starting Start gas or ether must not be used for this engineStarting the engine Starting with a weak battery Starting in cold conditionsDriving the machine Braking Cutting the engineBleeding in the event of fuel stoppage Engine stop250 500 1000 2000 MaintenanceMaintenance Schedule 250 500 1000 2000 Cleaning Cleaning the radiators heat exchanger Adjusting the pump and generator drive beltsRemoving the machine’s covers Checking radiatorgrillesChecking and adjusting the throttle control Adjusting the parking brakeReplacing the pump and generator drive belts Checking the exhaust systemCleaning the cyclone ﬁlter Servicing the air ﬁlterReplacing the air ﬁlter Emptying the particle trapChecking the Tyre Pressures Bleeding the fuel systemServicing the fuel ﬁlter Servicing the battery FusesChecking the Safety System FU2 FU9Replacing the bulb in the headlight Light setting Cutting Unit ComponentsAttaching and removing the cutting unit Side shifting the cutting unitImportant Information Setting the cutting height and tilt angle Cutting heightCutting Unit’s Service Position Placing in the Service PositionTilt angle Ground pressureReleasing the Service Position Cutting Unit ModelAlways replace the belts in pairs Replacing the power take-off beltsChecking the Blades Replacing the belt on the Combi unit Adjusting the power take-off beltsReplacing the cutting unit belt Removal of BioClip Plug Lubrication Lubrication ScheduleGeneral Lubricating the cablesHandle for cutting height setting Lubricating in Accordance with Lubrication SchedulePivot wheel bearings Cutting unit’s bevel gearPower take-off shaft’s front support bearing Lift cylinderEngine Oil Viscosity and qualityFilling engine oil Changing the Engine OilReplacing the engine’s oil ﬁlter Hydraulic oilInspection off the oil level Filling hydraulic oilHydraulic oil ﬁlter, change Cutting unit mountingLifting arm’s rear bearings Driver’s SeatParking brake cables Control cylinderLubrication Trouble Shooting Guide Problem CauseProblem Cause Problem Cause Trouble Shooting Guide Storage Winter StorageService Electrical system Hydraulic System Hydraulic System Fuel system Technical Data Data PT 26DTransmission Vibration levels4 Technical Data Diverse design standards Design standardsEU Declaration of Conformity only applies to Europe Design standards Page Page 1153893-26 ´z+Uy@¶6u¨ ´z+Uy@¶6u¨ Original instructions