Husqvarna PT26 D manual Maintenance Schedule, 250 500 1000 2000

Page 36

Maintenance

Chapter 6: Maintenance

It is good practice to always check for leaks and loose components after use. Also check the machine and listen for knocking sounds. During hard use and in extreme conditions, the service intervals should be reduced.

Check the cooling system’s antifreeze before the Winter.

Maintenance Schedule

The following is a list of maintenance procedures that must be performed on the machine. Paragraphs that are marked with footnote number 4, see an authorised service workshop.

● = Described in this manual

❍ = Not described in this manual.

Maintenance	Page	Daily main-		Weekly	Maintenance interval hours
		tenance		main-	250	500	1000		2000 3000
		befor after		tenance	250	500	1000		2000 3000
		befor after


Check for fuel and oil leaks	-	❍

Check the safety switch, seat	43	●

Check the safety switch pedal	43	●
system, neutral position

Check the engine oil level (at every	113	●		●
refuelling)

Check the hydraulic oil level	115	●		●

Check the coolant level	50	●		●

Check/clean the engine’s cooling air	38		●	●	●
intake, radiator mesh and radiator

Check fastenings (screws, nuts, etc.)	-		❍

Start the engine and blades, listen for	-		❍
unusual sounds

Clean under the cutting unit and belt	48		●	●	●
covers

Check for damage	-			❍

Check the air pressure in the tyres	41			●
(100 kPa)

Clean thoroughly around the engine	-			❍

Clean thoroughly around the	-			❍
transmission

Lubricate according to lubrication chart3	111			●	●
Clean the air ﬁlter and empty the	40			●		●
particle trap

Check the blades	50			●

Change the engine oil and ﬁlter1	114				●
Replace hydraulic oil ﬁlter and check	115				●
the oil level4, 5
Check the tension and condition of	38				●
the belts (generator belt, power take-	50
off belt, cutting unit belt)	50
off belt, cutting unit belt)	51
	51

35

Image 36

Contents PT26 D Contents Page Introduction CongratulationsDriving and Transport on Public Roads TowingProper Service Serial NumberSymbols and Decals Important Information Safety Instructions General UseWhen driving Driving on slopes Do as followsMaintenance ChildrenAvoid sparking and its consequences by Other protective devices are not ﬁtted or are defective Transport Environment protectionUser responsibility Presentation Placement of controls Speed control Parking brakeControl panel SeatAdjusting the cutting height Steering wheel and steering wheel consoleDifferential Lock FuellingControls on the control panel Control lever hydraulicsWinter fuel and parafﬁn precipitation Lifting the cutting unit transport positionSwitch for operation of cutting unit Switch for extra hydraulic function hydraulic kit optionIndicators trafﬁc kit option Push button for horn trafﬁc kit optionStarter switch HeadlightThrottle control High speedWeight transfer Spare Power outletRotating warning light trafﬁc kit option Parking lights trafﬁc kit optionAdjusting the steering wheel setting ChronometerLever for steering wheel console angle Rops Cooling system Cutting unit AntifreezeAccessories Driving Mowing TipsBefore Starting Start gas or ether must not be used for this engineStarting the engine Starting with a weak battery Starting in cold conditionsDriving the machine Braking Cutting the engineBleeding in the event of fuel stoppage Engine stopMaintenance Maintenance Schedule250 500 1000 2000 250 500 1000 2000 Cleaning Cleaning the radiators heat exchanger Adjusting the pump and generator drive beltsRemoving the machine’s covers Checking radiatorgrillesChecking and adjusting the throttle control Adjusting the parking brakeReplacing the pump and generator drive belts Checking the exhaust systemCleaning the cyclone ﬁlter Servicing the air ﬁlterReplacing the air ﬁlter Emptying the particle trapBleeding the fuel system Servicing the fuel ﬁlterChecking the Tyre Pressures Servicing the battery FusesChecking the Safety System FU2 FU9Replacing the bulb in the headlight Light setting Cutting Unit ComponentsAttaching and removing the cutting unit Side shifting the cutting unitImportant Information Setting the cutting height and tilt angle Cutting heightCutting Unit’s Service Position Placing in the Service PositionTilt angle Ground pressureReleasing the Service Position Cutting Unit ModelReplacing the power take-off belts Checking the BladesAlways replace the belts in pairs Adjusting the power take-off belts Replacing the cutting unit beltReplacing the belt on the Combi unit Removal of BioClip Plug Lubrication Lubrication ScheduleGeneral Lubricating the cablesHandle for cutting height setting Lubricating in Accordance with Lubrication SchedulePivot wheel bearings Cutting unit’s bevel gearPower take-off shaft’s front support bearing Lift cylinderEngine Oil Viscosity and qualityFilling engine oil Changing the Engine OilReplacing the engine’s oil ﬁlter Hydraulic oilInspection off the oil level Filling hydraulic oilHydraulic oil ﬁlter, change Cutting unit mountingLifting arm’s rear bearings Driver’s SeatParking brake cables Control cylinderLubrication Trouble Shooting Guide Problem CauseProblem Cause Problem Cause Trouble Shooting Guide Storage Winter StorageService Electrical system Hydraulic System Hydraulic System Fuel system Technical Data Data PT 26DTransmission Vibration levels4 Technical Data Design standards EU Declaration of Conformity only applies to EuropeDiverse design standards Design standards Page Page 1153893-26 ´z+Uy@¶6u¨ ´z+Uy@¶6u¨ Original instructions