Husqvarna PT26 D manual Removal of BioClip Plug

Page 53

Maintenance

	4.	Slacken off two screws and remove the three
	4.	Slacken off two screws and remove the three
		others for the gear housing. Turn the gear housing
		so that the belts can be moved under the pulley.
	5.	Check that the belt tensioning equipment is not
		jammed or binding and replace the spring.
	6.	Position the new belt and reinstall the gear
		housing.
	7.	Attach the new belt.
		The belt position decal is on the cutting unit under
		the protective cover.
	8.	Install the protective covers.
	8.	Install the protective covers.	Gearbox turned
	9.	Attach the cutting unit to the machine. See “Side	Gearbox turned
	9.	Attach the cutting unit to the machine. See “Side

shifting the cutting unit” on page 45.

Removal of BioClip Plug

To change a Combi unit from the BioClip function to a cutting unit with rear ejection, remove the BioClip plug, which is located under the unit.

1.Put the unit in the service position. See “The Cutting Unit’s Service Position” on page 48.

2.	Remove the screws holding the BioClip plug, and
	remove the plug.
	Tip: Fit the fully threaded screws	Removal of BioClip Plug
	M8x15 mm in the screw holes to protect the threads.
3.	Return the unit to the normal position.

Fit the BioClip plug in the reverse order.

52

Image 53

Contents PT26 D Contents Page Congratulations IntroductionDriving and Transport on Public Roads TowingSerial Number Proper ServiceSymbols and Decals Important Information General Use Safety InstructionsWhen driving Do as follows Driving on slopesChildren MaintenanceAvoid sparking and its consequences by Other protective devices are not ﬁtted or are defective Environment protection TransportUser responsibility Presentation Placement of controls Parking brake Speed controlSeat Control panelSteering wheel and steering wheel console Adjusting the cutting heightDifferential Lock FuellingControl lever hydraulics Controls on the control panelWinter fuel and parafﬁn precipitation Lifting the cutting unit transport positionSwitch for extra hydraulic function hydraulic kit option Switch for operation of cutting unitIndicators trafﬁc kit option Push button for horn trafﬁc kit optionHeadlight Starter switchThrottle control High speedSpare Power outlet Weight transferRotating warning light trafﬁc kit option Parking lights trafﬁc kit optionLever for steering wheel console angle Adjusting the steering wheel settingChronometer Rops Cooling system Antifreeze Cutting unitAccessories Mowing Tips DrivingStart gas or ether must not be used for this engine Before StartingStarting the engine Starting in cold conditions Starting with a weak batteryDriving the machine Cutting the engine BrakingBleeding in the event of fuel stoppage Engine stop250 500 1000 2000 MaintenanceMaintenance Schedule 250 500 1000 2000 Cleaning Adjusting the pump and generator drive belts Cleaning the radiators heat exchangerRemoving the machine’s covers Checking radiatorgrillesAdjusting the parking brake Checking and adjusting the throttle controlReplacing the pump and generator drive belts Checking the exhaust systemServicing the air ﬁlter Cleaning the cyclone ﬁlterReplacing the air ﬁlter Emptying the particle trapChecking the Tyre Pressures Bleeding the fuel systemServicing the fuel ﬁlter Fuses Servicing the batteryFU2 FU9 Checking the Safety SystemReplacing the bulb in the headlight Cutting Unit Components Light settingAttaching and removing the cutting unit Side shifting the cutting unitImportant Information Cutting height Setting the cutting height and tilt anglePlacing in the Service Position Cutting Unit’s Service PositionTilt angle Ground pressureCutting Unit Model Releasing the Service PositionAlways replace the belts in pairs Replacing the power take-off beltsChecking the Blades Replacing the belt on the Combi unit Adjusting the power take-off beltsReplacing the cutting unit belt Removal of BioClip Plug Lubrication Schedule LubricationGeneral Lubricating the cablesLubricating in Accordance with Lubrication Schedule Handle for cutting height settingPivot wheel bearings Cutting unit’s bevel gearLift cylinder Power take-off shaft’s front support bearingEngine Oil Viscosity and qualityChanging the Engine Oil Filling engine oilHydraulic oil Replacing the engine’s oil ﬁlterInspection off the oil level Filling hydraulic oilCutting unit mounting Hydraulic oil ﬁlter, changeLifting arm’s rear bearings Driver’s SeatControl cylinder Parking brake cablesLubrication Problem Cause Trouble Shooting GuideProblem Cause Problem Cause Trouble Shooting Guide Winter Storage StorageService Electrical system Hydraulic System Hydraulic System Fuel system Data PT 26D Technical DataTransmission Vibration levels4 Technical Data Diverse design standards Design standardsEU Declaration of Conformity only applies to Europe Design standards Page Page Original instructions 1153893-26 ´z+Uy@¶6u¨ ´z+Uy@¶6u¨