Husqvarna PT26 D Replacing the engine’s oil filter, Hydraulic oil, Inspection off the oil level

Page 58

Lubrication

7. Replacing the engine’s oil filter

WARNING:

Risk of spray and burn injuries. The engine’s oil filter may be very hot immediately after stopping. Allow the engine to cool somewhat first.

Engine oil filter

IMPORTANT INFORMATION:

Replaced filters must be handed in to the workshop or other allotted place for disposal.

Avoid skin contact; wash with soap and water in case of spills.

1.Remove the oil filter. If necessary, use a filter remover.

2.Clean the oil filter’s mounting.

3.Wipe new, clean engine oil onto the seal for the new filter.

4.Fit the filter by hand until it mates + 3/4 turns.

5.Run the engine warm, then check that there are no leaks around the oil filter seal.

6.Check the oil level in the engine, top up if necessary. The oil filter holds 0.2 litres of oil.

8. Hydraulic oil

Viscosity and quality

Hydraulic oil ISO VG.

Viscosity 46 cSt.

Local regulations may affect the choice of hydraulic oil due to environmental reasons, consult your Husqvarna workshop at the relevant location.

Inspection off the oil level

Open the right-hand engine cover and check the level against the level marking. The level should be between the MAX and MIN line.

Filling hydraulic oil

Remove the engine cover. See “Engine cover” on page 79. Fill with hydraulic oil to approximately 60 mm (2 1/4”) below the strainer’s upper edge.

Oil level, hydraulic tank

57

Page 57 Page 59
Image 58
Page 57 Page 59
Contents PT26 D Contents Page Driving and Transport on Public Roads IntroductionCongratulations TowingProper Service Serial NumberSymbols and Decals Important Information Safety Instructions General UseWhen driving Driving on slopes Do as followsMaintenance ChildrenAvoid sparking and its consequences by Other protective devices are not fitted or are defective Transport Environment protectionUser responsibility Presentation Placement of controls Speed control Parking brakeControl panel SeatDifferential Lock Adjusting the cutting heightSteering wheel and steering wheel console FuellingWinter fuel and paraffin precipitation Controls on the control panelControl lever hydraulics Lifting the cutting unit transport positionIndicators traffic kit option Switch for operation of cutting unitSwitch for extra hydraulic function hydraulic kit option Push button for horn traffic kit optionThrottle control Starter switchHeadlight High speedRotating warning light traffic kit option Weight transferSpare Power outlet Parking lights traffic kit optionChronometer Adjusting the steering wheel settingLever for steering wheel console angle Rops Cooling system Cutting unit AntifreezeAccessories Driving Mowing TipsBefore Starting Start gas or ether must not be used for this engineStarting the engine Starting with a weak battery Starting in cold conditionsDriving the machine Bleeding in the event of fuel stoppage BrakingCutting the engine Engine stopMaintenance Schedule Maintenance250 500 1000 2000 250 500 1000 2000 Cleaning Removing the machine’s covers Cleaning the radiators heat exchangerAdjusting the pump and generator drive belts Checking radiatorgrillesReplacing the pump and generator drive belts Checking and adjusting the throttle controlAdjusting the parking brake Checking the exhaust systemReplacing the air filter Cleaning the cyclone filterServicing the air filter Emptying the particle trapServicing the fuel filter Bleeding the fuel systemChecking the Tyre Pressures Servicing the battery FusesChecking the Safety System FU2 FU9Replacing the bulb in the headlight Attaching and removing the cutting unit Light settingCutting Unit Components Side shifting the cutting unitImportant Information Setting the cutting height and tilt angle Cutting heightTilt angle Cutting Unit’s Service PositionPlacing in the Service Position Ground pressureReleasing the Service Position Cutting Unit ModelChecking the Blades Replacing the power take-off beltsAlways replace the belts in pairs Replacing the cutting unit belt Adjusting the power take-off beltsReplacing the belt on the Combi unit Removal of BioClip Plug General LubricationLubrication Schedule Lubricating the cablesPivot wheel bearings Handle for cutting height settingLubricating in Accordance with Lubrication Schedule Cutting unit’s bevel gearEngine Oil Power take-off shaft’s front support bearingLift cylinder Viscosity and qualityFilling engine oil Changing the Engine OilInspection off the oil level Replacing the engine’s oil filterHydraulic oil Filling hydraulic oilLifting arm’s rear bearings Hydraulic oil filter, changeCutting unit mounting Driver’s SeatParking brake cables Control cylinderLubrication Trouble Shooting Guide Problem CauseProblem Cause Problem Cause Trouble Shooting Guide Storage Winter StorageService Electrical system Hydraulic System Hydraulic System Fuel system Technical Data Data PT 26DTransmission Vibration levels4 Technical Data EU Declaration of Conformity only applies to Europe Design standardsDiverse design standards Design standards Page Page 1153893-26 ´z+Uy@¶6u¨ ´z+Uy@¶6u¨ Original instructions
Top Page Image Contents