Husqvarna PT26 D manual Placement of controls

Page 17

Presentation

Placement of controls

1.

Speed control for driving forwards page 17

9.

Knob for seat suspension page 18

2.

Speed control for reversing page 17

10.

Steering wheel console page 17

3.

Parking brake page 17

11.

Pedal for differential lock page 19

4.

Control panel page 16

12.

Cranks for setting cutting height page 19

5.

Knob for the backrest rake page 18

13.

Fuel tank cover page 19

6.Catch for seat folding page 18

7.Knob for the lumbar support page 18

8.Lever for lateral seat adjustment page 18

 

Control panel

 

-

21.

Control lever hydraulics page 20

30.

Switch for weight transfer page 23

22.

Switch for operating the cutting unit page 21

31.

Rotating warning light (option) page 23

23.

Switch for 2nd hydraulic function (option) page 21

32.

Parking lights (option) page 23

24.

Horn switch (option) page 21

33.

Spare

25.

Turn signal lights switch (option) page 21

34.

Power outlet page 23

26.

Starter switch page 22

35.

Mains switch power outlet page 23

27.

Switch for the lights page 22

36.

Chronometer page 24

28.Throttle control page 22

29.Switch for high and low speed page 22

16

Page 16 Page 18
Image 17
Page 16 Page 18
Contents PT26 D Contents Page Congratulations IntroductionDriving and Transport on Public Roads TowingSerial Number Proper ServiceSymbols and Decals Important Information General Use Safety InstructionsWhen driving Do as follows Driving on slopesChildren MaintenanceAvoid sparking and its consequences by Other protective devices are not fitted or are defective Environment protection TransportUser responsibility Presentation Placement of controls Parking brake Speed controlSeat Control panelSteering wheel and steering wheel console Adjusting the cutting heightDifferential Lock FuellingControl lever hydraulics Controls on the control panelWinter fuel and paraffin precipitation Lifting the cutting unit transport positionSwitch for extra hydraulic function hydraulic kit option Switch for operation of cutting unitIndicators traffic kit option Push button for horn traffic kit optionHeadlight Starter switchThrottle control High speedSpare Power outlet Weight transferRotating warning light traffic kit option Parking lights traffic kit optionLever for steering wheel console angle Adjusting the steering wheel settingChronometer Rops Cooling system Antifreeze Cutting unitAccessories Mowing Tips DrivingStart gas or ether must not be used for this engine Before StartingStarting the engine Starting in cold conditions Starting with a weak batteryDriving the machine Cutting the engine BrakingBleeding in the event of fuel stoppage Engine stop250 500 1000 2000 MaintenanceMaintenance Schedule 250 500 1000 2000 Cleaning Adjusting the pump and generator drive belts Cleaning the radiators heat exchangerRemoving the machine’s covers Checking radiatorgrillesAdjusting the parking brake Checking and adjusting the throttle controlReplacing the pump and generator drive belts Checking the exhaust systemServicing the air filter Cleaning the cyclone filterReplacing the air filter Emptying the particle trapChecking the Tyre Pressures Bleeding the fuel systemServicing the fuel filter Fuses Servicing the batteryFU2 FU9 Checking the Safety SystemReplacing the bulb in the headlight Cutting Unit Components Light settingAttaching and removing the cutting unit Side shifting the cutting unitImportant Information Cutting height Setting the cutting height and tilt anglePlacing in the Service Position Cutting Unit’s Service PositionTilt angle Ground pressureCutting Unit Model Releasing the Service PositionAlways replace the belts in pairs Replacing the power take-off beltsChecking the Blades Replacing the belt on the Combi unit Adjusting the power take-off beltsReplacing the cutting unit belt Removal of BioClip Plug Lubrication Schedule LubricationGeneral Lubricating the cablesLubricating in Accordance with Lubrication Schedule Handle for cutting height settingPivot wheel bearings Cutting unit’s bevel gearLift cylinder Power take-off shaft’s front support bearingEngine Oil Viscosity and qualityChanging the Engine Oil Filling engine oilHydraulic oil Replacing the engine’s oil filterInspection off the oil level Filling hydraulic oilCutting unit mounting Hydraulic oil filter, changeLifting arm’s rear bearings Driver’s SeatControl cylinder Parking brake cablesLubrication Problem Cause Trouble Shooting GuideProblem Cause Problem Cause Trouble Shooting Guide Winter Storage StorageService Electrical system Hydraulic System Hydraulic System Fuel system Data PT 26D Technical DataTransmission Vibration levels4 Technical Data Diverse design standards Design standardsEU Declaration of Conformity only applies to Europe Design standards Page Page Original instructions 1153893-26 ´z+Uy@¶6u¨ ´z+Uy@¶6u¨
Top Page Image Contents