Husqvarna PT26 D Light setting, Cutting Unit Components, Attaching and removing the cutting unit

Page 46

Maintenance

IMPORTANT INFORMATION:

Do not touch the bulb glass with your ﬁngers. Finger prints evaporate and mark the reﬂector.

5.Fold the wire loop for headlight lamp to one side and replace the bulb.

6.Assemble in the reverse order.

Light setting

Place the machine at least 5 m from a wall. The machine must stand ﬂat.

The steering wheel console must be in the rear position.

Switch on the headlights.

The low beam's upper limit line must fall 1 cm for each metre distance to the wall, measure from the centre of the headlight.

Adjust with the screws (36) if necessary. These are accessible once the rear plastic cover around the steering wheel console has been removed.

The Cutting Unit Components

The components mentioned are:

•	A Pin
•	B Link joint
• C Cutting unit mountings
• D Cutting height settings
• E Propeller shaft with quick couplings
•	F Service handle
• G Drive belt with cover		The Cutting Unit Components
		The Cutting Unit Components

•H Bevel gear

Attaching and removing the cutting unit

WARNING:

Exercise caution. Risk of crush injuries. Wear protective gloves

See “Side shifting the cutting unit” on page 45.

Side shifting the cutting unit

Cutting unit, Combi 155, can be side shifted 8 cm to the left or be centrally positioned on the machine.

1. Stop the engine. Switch off the weight transfer switch.

45

Image 46

Contents PT26 D Contents Page Driving and Transport on Public Roads IntroductionCongratulations TowingProper Service Serial NumberSymbols and Decals Important Information Safety Instructions General UseWhen driving Driving on slopes Do as followsMaintenance ChildrenAvoid sparking and its consequences by Other protective devices are not ﬁtted or are defective Transport Environment protectionUser responsibility Presentation Placement of controls Speed control Parking brakeControl panel SeatDifferential Lock Adjusting the cutting heightSteering wheel and steering wheel console FuellingWinter fuel and parafﬁn precipitation Controls on the control panelControl lever hydraulics Lifting the cutting unit transport positionIndicators trafﬁc kit option Switch for operation of cutting unitSwitch for extra hydraulic function hydraulic kit option Push button for horn trafﬁc kit optionThrottle control Starter switchHeadlight High speedRotating warning light trafﬁc kit option Weight transferSpare Power outlet Parking lights trafﬁc kit optionChronometer Adjusting the steering wheel settingLever for steering wheel console angle Rops Cooling system Cutting unit AntifreezeAccessories Driving Mowing TipsBefore Starting Start gas or ether must not be used for this engineStarting the engine Starting with a weak battery Starting in cold conditionsDriving the machine Bleeding in the event of fuel stoppage BrakingCutting the engine Engine stopMaintenance Schedule Maintenance250 500 1000 2000 250 500 1000 2000 Cleaning Removing the machine’s covers Cleaning the radiators heat exchangerAdjusting the pump and generator drive belts Checking radiatorgrillesReplacing the pump and generator drive belts Checking and adjusting the throttle controlAdjusting the parking brake Checking the exhaust systemReplacing the air ﬁlter Cleaning the cyclone ﬁlterServicing the air ﬁlter Emptying the particle trapServicing the fuel ﬁlter Bleeding the fuel systemChecking the Tyre Pressures Servicing the battery FusesChecking the Safety System FU2 FU9Replacing the bulb in the headlight Attaching and removing the cutting unit Light settingCutting Unit Components Side shifting the cutting unitImportant Information Setting the cutting height and tilt angle Cutting heightTilt angle Cutting Unit’s Service PositionPlacing in the Service Position Ground pressureReleasing the Service Position Cutting Unit ModelChecking the Blades Replacing the power take-off beltsAlways replace the belts in pairs Replacing the cutting unit belt Adjusting the power take-off beltsReplacing the belt on the Combi unit Removal of BioClip Plug General LubricationLubrication Schedule Lubricating the cablesPivot wheel bearings Handle for cutting height settingLubricating in Accordance with Lubrication Schedule Cutting unit’s bevel gearEngine Oil Power take-off shaft’s front support bearingLift cylinder Viscosity and qualityFilling engine oil Changing the Engine OilInspection off the oil level Replacing the engine’s oil ﬁlterHydraulic oil Filling hydraulic oilLifting arm’s rear bearings Hydraulic oil ﬁlter, changeCutting unit mounting Driver’s SeatParking brake cables Control cylinderLubrication Trouble Shooting Guide Problem CauseProblem Cause Problem Cause Trouble Shooting Guide Storage Winter StorageService Electrical system Hydraulic System Hydraulic System Fuel system Technical Data Data PT 26DTransmission Vibration levels4 Technical Data EU Declaration of Conformity only applies to Europe Design standardsDiverse design standards Design standards Page Page 1153893-26 ´z+Uy@¶6u¨ ´z+Uy@¶6u¨ Original instructions