Husqvarna PT26 D manual Starter switch, Headlight, Throttle control, High speed

Page 23

Presentation

26. Starter switch

Three positions:

• OFF

All functions switched off. The engine is stopped. The parking light can be switched on (trafﬁc kit option).

• ON

Normal operating position.

• Start and Preheating

Keep the switch in the glow plug mode, when glow plug heating is complete the starter is engaged.

During glow plug heating, light (43) on the indicator Starter switch panel comes on. Non-locking to position ON.

Turning again within 2 seconds gives starting without glow plug heating.

27. Headlight

Three positions, clockwise in the following order:

• Off:

• Dipped beam

• Full beam

If the switch is moved to the Dipped beam position automatic dipped beam mode, dipped beam is switched on when the engine is running.

Switch for headlight

28. Throttle control

The accelerator is used to control the speed of the engine and thereby also the rotation speed of the blades.

In order to increase or decrease the engine speed, the control is moved forwards or backwards respectively.

29. High speed

Activated switch. This switch is used to select either high or low speed.

The speed must drop to zero before the machine shifts to low speed if high speed is actuated.

If the differential lock is actuated, the machine will not shift to high speed until the pedal is released.

Front wheel drive is engaged in high speed mode.

All wheel drive is engaged in low speed mode.

The differential lock and cutting unit only work in low speed mode.

Throttle control

High speed

22

Image 23

Contents PT26 D Contents Page Towing IntroductionCongratulations Driving and Transport on Public RoadsSerial Number Proper ServiceSymbols and Decals Important Information General Use Safety InstructionsWhen driving Do as follows Driving on slopesChildren MaintenanceAvoid sparking and its consequences by Other protective devices are not ﬁtted or are defective Environment protection TransportUser responsibility Presentation Placement of controls Parking brake Speed controlSeat Control panelFuelling Adjusting the cutting heightSteering wheel and steering wheel console Differential LockLifting the cutting unit transport position Controls on the control panelControl lever hydraulics Winter fuel and parafﬁn precipitationPush button for horn trafﬁc kit option Switch for operation of cutting unitSwitch for extra hydraulic function hydraulic kit option Indicators trafﬁc kit optionHigh speed Starter switchHeadlight Throttle controlParking lights trafﬁc kit option Weight transferSpare Power outlet Rotating warning light trafﬁc kit optionLever for steering wheel console angle Adjusting the steering wheel settingChronometer Rops Cooling system Antifreeze Cutting unitAccessories Mowing Tips DrivingStart gas or ether must not be used for this engine Before StartingStarting the engine Starting in cold conditions Starting with a weak batteryDriving the machine Engine stop BrakingCutting the engine Bleeding in the event of fuel stoppage250 500 1000 2000 MaintenanceMaintenance Schedule 250 500 1000 2000 Cleaning Checking radiatorgrilles Cleaning the radiators heat exchangerAdjusting the pump and generator drive belts Removing the machine’s coversChecking the exhaust system Checking and adjusting the throttle controlAdjusting the parking brake Replacing the pump and generator drive beltsEmptying the particle trap Cleaning the cyclone ﬁlterServicing the air ﬁlter Replacing the air ﬁlterChecking the Tyre Pressures Bleeding the fuel systemServicing the fuel ﬁlter Fuses Servicing the batteryFU2 FU9 Checking the Safety SystemReplacing the bulb in the headlight Side shifting the cutting unit Light settingCutting Unit Components Attaching and removing the cutting unitImportant Information Cutting height Setting the cutting height and tilt angleGround pressure Cutting Unit’s Service PositionPlacing in the Service Position Tilt angleCutting Unit Model Releasing the Service PositionAlways replace the belts in pairs Replacing the power take-off beltsChecking the Blades Replacing the belt on the Combi unit Adjusting the power take-off beltsReplacing the cutting unit belt Removal of BioClip Plug Lubricating the cables LubricationLubrication Schedule GeneralCutting unit’s bevel gear Handle for cutting height settingLubricating in Accordance with Lubrication Schedule Pivot wheel bearingsViscosity and quality Power take-off shaft’s front support bearingLift cylinder Engine OilChanging the Engine Oil Filling engine oilFilling hydraulic oil Replacing the engine’s oil ﬁlterHydraulic oil Inspection off the oil levelDriver’s Seat Hydraulic oil ﬁlter, changeCutting unit mounting Lifting arm’s rear bearingsControl cylinder Parking brake cablesLubrication Problem Cause Trouble Shooting GuideProblem Cause Problem Cause Trouble Shooting Guide Winter Storage StorageService Electrical system Hydraulic System Hydraulic System Fuel system Data PT 26D Technical DataTransmission Vibration levels4 Technical Data Diverse design standards Design standardsEU Declaration of Conformity only applies to Europe Design standards Page Page Original instructions 1153893-26 ´z+Uy@¶6u¨ ´z+Uy@¶6u¨