Husqvarna PT26 D Hydraulic oil ﬁlter, change, Cutting unit mounting, Lifting arm’s rear bearings

Page 59

Lubrication

Changing hydraulic oil

IMPORTANT INFORMATION:

Used hydraulic oil is a health hazard and must not be disposed of in the ground or in nature.

Replaced ﬁlters must be handed in to the workshop or other allotted place for disposal.

Avoid skin contact; wash with soap and water in case of spills.

Hydraulic oil and ﬁlters should be changed by an authorised Husqvarna workshop.

8. Hydraulic oil ﬁlter, change

Hydraulic oil ﬁlters should be changed by an authorised Husqvarna workshop.

9. Cutting unit mounting

Lubricate ball joints and shafts with the oil can.

Cutting unit mounting

10. Lifting arm’s rear bearings

2 nipples, one on each side. Lubricate using a grease gun until grease is forced out.

Rear storage bearing

11. Driver’s Seat

Tilt the seat back.

Lubricate the lengthways adjustment mechanism with the oilcan.

Lubricate the lengthways adjustment runners with grease. Pull the seat back and forth and lubricate on both sides.

Driver’s Seat

58

Image 59

Contents PT26 D Contents Page Towing IntroductionCongratulations Driving and Transport on Public RoadsSerial Number Proper ServiceSymbols and Decals Important Information General Use Safety InstructionsWhen driving Do as follows Driving on slopesChildren MaintenanceAvoid sparking and its consequences by Other protective devices are not ﬁtted or are defective Environment protection TransportUser responsibility Presentation Placement of controls Parking brake Speed controlSeat Control panelFuelling Adjusting the cutting heightSteering wheel and steering wheel console Differential LockLifting the cutting unit transport position Controls on the control panelControl lever hydraulics Winter fuel and parafﬁn precipitationPush button for horn trafﬁc kit option Switch for operation of cutting unitSwitch for extra hydraulic function hydraulic kit option Indicators trafﬁc kit optionHigh speed Starter switchHeadlight Throttle controlParking lights trafﬁc kit option Weight transferSpare Power outlet Rotating warning light trafﬁc kit optionLever for steering wheel console angle Adjusting the steering wheel settingChronometer Rops Cooling system Antifreeze Cutting unitAccessories Mowing Tips DrivingStart gas or ether must not be used for this engine Before StartingStarting the engine Starting in cold conditions Starting with a weak batteryDriving the machine Engine stop BrakingCutting the engine Bleeding in the event of fuel stoppage250 500 1000 2000 MaintenanceMaintenance Schedule 250 500 1000 2000 Cleaning Checking radiatorgrilles Cleaning the radiators heat exchangerAdjusting the pump and generator drive belts Removing the machine’s coversChecking the exhaust system Checking and adjusting the throttle controlAdjusting the parking brake Replacing the pump and generator drive beltsEmptying the particle trap Cleaning the cyclone ﬁlterServicing the air ﬁlter Replacing the air ﬁlterChecking the Tyre Pressures Bleeding the fuel systemServicing the fuel ﬁlter Fuses Servicing the batteryFU2 FU9 Checking the Safety SystemReplacing the bulb in the headlight Side shifting the cutting unit Light settingCutting Unit Components Attaching and removing the cutting unitImportant Information Cutting height Setting the cutting height and tilt angleGround pressure Cutting Unit’s Service PositionPlacing in the Service Position Tilt angleCutting Unit Model Releasing the Service PositionAlways replace the belts in pairs Replacing the power take-off beltsChecking the Blades Replacing the belt on the Combi unit Adjusting the power take-off beltsReplacing the cutting unit belt Removal of BioClip Plug Lubricating the cables LubricationLubrication Schedule GeneralCutting unit’s bevel gear Handle for cutting height settingLubricating in Accordance with Lubrication Schedule Pivot wheel bearingsViscosity and quality Power take-off shaft’s front support bearingLift cylinder Engine OilChanging the Engine Oil Filling engine oilFilling hydraulic oil Replacing the engine’s oil ﬁlterHydraulic oil Inspection off the oil levelDriver’s Seat Hydraulic oil ﬁlter, changeCutting unit mounting Lifting arm’s rear bearingsControl cylinder Parking brake cablesLubrication Problem Cause Trouble Shooting GuideProblem Cause Problem Cause Trouble Shooting Guide Winter Storage StorageService Electrical system Hydraulic System Hydraulic System Fuel system Data PT 26D Technical DataTransmission Vibration levels4 Technical Data Diverse design standards Design standardsEU Declaration of Conformity only applies to Europe Design standards Page Page Original instructions 1153893-26 ´z+Uy@¶6u¨ ´z+Uy@¶6u¨