Husqvarna PT26 D manual Other protective devices are not ﬁtted or are defective

Page 13

Safety Instructions

ﬂammable liquids are stored in an open container.

Do not work on the starter motor circuit in the vicinity of spilt fuel.

Disconnect the battery's power connection cable (usually the black negative cable) ﬁrst and connect it last.

Exercise care with tools so that short circuiting does not occur.

Do not short circuit across the starter relay's connections to run the starter motor.

•Be especially careful when handling battery acid. Acid on the skin can cause serious corrosive injuries. In the event of spillage on the skin wash immediately with water.

•Acid in the eyes can cause blindness, contact a doctor immediately.

•Be careful when servicing the battery. Explosive

gases form in the battery. Never perform maintenance on the battery while smoking or in the vicinity of open ﬂames or sparks. This can cause the battery to explode and cause serious injuries.

• Make sure all nuts and bolts are tightened correctly and that the equipment is in good condition.

•Do not modify safety equipment. Check regularly to be sure it works properly. The machine must not be driven

	if protective plates, protective covers, safety switches or	Do not smoke when carrying out maintenance
	other protective devices are not ﬁtted or are defective.	Do not smoke when carrying out maintenance
	other protective devices are not ﬁtted or are defective.

• Do not change the settings of governors and avoid running the engine with overly high engine speeds. If you run too fast, you risk damaging the machine components.

• Never use the machine indoors or in spaces lacking

proper ventilation. Exhaust fumes contain carbon
monoxide, an odourless, poisonous and highly
dangerous gas.
• Stop and inspect the equipment if you run over or into
anything. If necessary, make repairs before starting.
• Never make adjustments with the engine running.
• The machine is tested and approved only with the
equipment originally provided or recommended by the
manufacturer.
• The blades are sharp and can cause cuts and gashes.
Wrap the blades or wear protective gloves when
handling them.
• Check the parking brake’s functionality regularly. Adjust	Never drive the machine in an enclosed space
and maintain as required.
• The mulching unit should only be used where better
quality mowing is required and in known areas.

12

Image 13

Contents PT26 D Contents Page Congratulations IntroductionDriving and Transport on Public Roads TowingSerial Number Proper ServiceSymbols and Decals Important Information General Use Safety InstructionsWhen driving Do as follows Driving on slopesChildren MaintenanceAvoid sparking and its consequences by Other protective devices are not ﬁtted or are defective Environment protection TransportUser responsibility Presentation Placement of controls Parking brake Speed controlSeat Control panelSteering wheel and steering wheel console Adjusting the cutting heightDifferential Lock FuellingControl lever hydraulics Controls on the control panelWinter fuel and parafﬁn precipitation Lifting the cutting unit transport positionSwitch for extra hydraulic function hydraulic kit option Switch for operation of cutting unitIndicators trafﬁc kit option Push button for horn trafﬁc kit optionHeadlight Starter switchThrottle control High speedSpare Power outlet Weight transferRotating warning light trafﬁc kit option Parking lights trafﬁc kit optionChronometer Adjusting the steering wheel settingLever for steering wheel console angle Rops Cooling system Antifreeze Cutting unitAccessories Mowing Tips DrivingStart gas or ether must not be used for this engine Before StartingStarting the engine Starting in cold conditions Starting with a weak batteryDriving the machine Cutting the engine BrakingBleeding in the event of fuel stoppage Engine stopMaintenance Schedule Maintenance250 500 1000 2000 250 500 1000 2000 Cleaning Adjusting the pump and generator drive belts Cleaning the radiators heat exchangerRemoving the machine’s covers Checking radiatorgrillesAdjusting the parking brake Checking and adjusting the throttle controlReplacing the pump and generator drive belts Checking the exhaust systemServicing the air ﬁlter Cleaning the cyclone ﬁlterReplacing the air ﬁlter Emptying the particle trapServicing the fuel ﬁlter Bleeding the fuel systemChecking the Tyre Pressures Fuses Servicing the batteryFU2 FU9 Checking the Safety SystemReplacing the bulb in the headlight Cutting Unit Components Light settingAttaching and removing the cutting unit Side shifting the cutting unitImportant Information Cutting height Setting the cutting height and tilt anglePlacing in the Service Position Cutting Unit’s Service PositionTilt angle Ground pressureCutting Unit Model Releasing the Service PositionChecking the Blades Replacing the power take-off beltsAlways replace the belts in pairs Replacing the cutting unit belt Adjusting the power take-off beltsReplacing the belt on the Combi unit Removal of BioClip Plug Lubrication Schedule LubricationGeneral Lubricating the cablesLubricating in Accordance with Lubrication Schedule Handle for cutting height settingPivot wheel bearings Cutting unit’s bevel gearLift cylinder Power take-off shaft’s front support bearingEngine Oil Viscosity and qualityChanging the Engine Oil Filling engine oilHydraulic oil Replacing the engine’s oil ﬁlterInspection off the oil level Filling hydraulic oilCutting unit mounting Hydraulic oil ﬁlter, changeLifting arm’s rear bearings Driver’s SeatControl cylinder Parking brake cablesLubrication Problem Cause Trouble Shooting GuideProblem Cause Problem Cause Trouble Shooting Guide Winter Storage StorageService Electrical system Hydraulic System Hydraulic System Fuel system Data PT 26D Technical DataTransmission Vibration levels4 Technical Data EU Declaration of Conformity only applies to Europe Design standardsDiverse design standards Design standards Page Page Original instructions 1153893-26 ´z+Uy@¶6u¨ ´z+Uy@¶6u¨